background image

18

ADJUSTING

 

/

 

REPLACING

 

KNIVES

WARNING

These indexable insert helical cutterheads are designed 
for 40300H Only.

These instructions make reference to many procedures 
detailed in your planer manual. Always consult your 
manual for these procedures.

INVENTORY (Figure 6.)

A. Helical 

Cutterhead

B.  

Flat Head Torx Screw M5 x 8.8   

 

 

C. Cutting 

Tips

ROTATING/ CHANGING 
HIGH SPEED STEEL CUTTING TIPS

Tools Needed:
T-Handle Wrench with T25 Torx Bit

The 13” cutterhead is equipped with 26 indexable high 
speed steel 

cutting tips

. Each 

cutting tip

 can be rotated 

to reveal any one of its 2 cutting edges. If one cutting 
edge becomes dull or damaged, users may simply rotate 
the 

cutting tip

 by 90 degrees to index to a fresh cutting 

edge (Fig. 7).

Each tip has a referencing dot at the corner. If the tip is 
roated, the reference dot location will be used as an 
indicator to tell if it is used or new. 

To rotate or change a HSS cutting tip:

1. DISCONNECT THE PLANER FROM THE POWER 
SOURCE!

2. Loosen 2 hex head screws from dust chute by hex 
wrench. Remove Dust chute.

3.  Remove any sawdust from the head of the HSS tip 
Torx screw.

4.  Insert hex wrench into right side panel & cutterhead 
and turn the cutterhead to a position for changing tips. 

SEE FIG. 7A

5.  Remove the Torx screw and HSS Cutting Tip.

6.  Clean all dust and dirt off the cutting tip and the 
cutterhead pocket from which the cutting tip was 
removed, and replace the cutting tip so a fresh, sharp 
edge is facing outward.

NOTE: Proper cleaning is critical to achieving a smooth 
finish. Dirt or dust trapped between the cutting tip and 
cutterhead will slightly raise the cutting tip, and make a 
noticeable marks on your work-pieces the next time you 
plane.

7. Lubricate the Torx screw threads with a light machine 
oil, wipe the excess oil off the threads, and torque the 
Torx screw to 48-52 in-lbs.

Cutterhead knives and inserts are razor sharp! 
Always wear heavy leather golves when handling 
cutterheads, and avoid contact with ctips whenever 
possible. Failure to comply can result in serious 
personal injury!

A

B

C

Reference Dot

Fig. 7

Fig. 6

All manuals and user guides at all-guides.com

Summary of Contents for 40300H



































Reviews: