ESP
AÑOL
Storage & Care
Cómo Ensamblar Su
Trapeador a Vapor Niebla Limpia
11
PROPER STORAGE
Preparing your Clean Mist Steam Mop for storage is quick and simple. When you have finished
your mopping tasks, follow the steps listed below.
1.
Gently press down on On/Off Switch until it
clicks
– red Power Indicator Light will turn off.
Unplug power cord from electrical outlet.
2.
Place Mop Head on top of Resting Pad, and allow unit to fully cool (30 minutes).
3.
For convenience it is recommended to disconnect Telescopic Pole, and if attached, remove
Microfiber Pad from Mop Head. If Pad is dirty you may wash it, either by hand or in a washing
machine. Allow to air-dry.
4.
Unscrew and remove Boiler Cap. Drain any water remaining in Boiler into a sink or tub, to
minimize potential mineral build-up and prevent overfilling during next use. Replace Cap (do
not fully tighten).
NOTE: It is not necessary to drain any Cleanfast HARD FLOOR Solution remaining
inside Solution Tank.
5.
Reconnect Telescopic Pole. For storage purposes, you may wish to collapse Telescopic Pole
to its shortest length. Refer to Page 6 for details.
6.
Wrap power cord around Cord Brackets.
7.
Store Clean Mist Steam Mop in a cool, dry location, along with all included accessories.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may limit the
effectiveness and reduce the life of your Clean Mist Steam Mop.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your Clean Mist Steam Mop.
In addition, it is recommended that the Boiler be cleaned at
least once a month in order to remove any deposits that form. This will help to extend the life of
your Clean Mist Steam Mop and keep it functioning at its maximum potential.
To remove mineral build-up:
1.
Gently press down on On/Off Switch until it
clicks
– red Power Indicator Light will turn off.
Unplug power cord from electrical outlet.
IMPORTANT: Unit should remain off and unplugged during cleaning procedure.
2.
Place Mop Head on top of Resting Pad, and allow unit to fully cool (30 minutes).
3.
For convenience it is recommended to disconnect Telescopic Pole, and if attached, remove
Microfiber Pad from Mop Head. Leaving them off during cleaning will make the process easier.
4.
Remove Boiler Cap and drain any water remaining in Boiler into a sink or tub.
5.
Using Measuring Cup, make a mixture of 3.4 oz. (100 ml.) water and 3.4 oz. (100 ml.) vinegar.
6.
Pour water/vinegar solution into Boiler.
7.
Allow water/vinegar solution to soak in boiler for 30-40 minutes.
8.
Drain water/vinegar solution from Boiler into a sink or tub. Refill Boiler with fresh water, drain
and repeat until vinegar odor dissipates.
9.
Replace Boiler Cap (do not fully tighten), reconnect Telescopic Pole and store your Clean Mist
Steam Mop as usual.
1-A
1-B
1-C
1-D
1-E
FIGURA 1
6
TUBO TELESCÓPICO
1.
Conecte la Manija al extremo superior (más ancho) del Tubo Telescópico. Para esto, simplemente
deslice la Manija en el Tubo hasta que quede fija en su lugar (FIGURA 1-A).
NOTA: Una vez conectada, la Manija está diseñada para no ser retirada del Tubo Telescópico.
Si se requiere retirarla, contacte a Servicio al Cliente para asistencia (página 13).
2.
Introduzca el extremo inferior (más angosto) del Tubo Telescópico en la yunta encima del Cabezal
del Trapeador. Cuando lo introduzca, asegúrese de que el botón de liberación del Tubo quede en la
parte trasera de la yunta, como se ilustra (FIGURA 1-B).
3.
Presione el Tubo Telescópico en la yunta hasta que el botón de liberación quede fijo dentro del
pequeño agujero detrás de la abrazadera (FIGURA 1-C). Ahora el Tubo debe estar asegurado dentro
del Cabezal del Trapeador.
NOTA: A fin de lograr pasar el botón de liberación por el agujero, puede ser necesario rotar y
ajustar el Tubo Telescópico hasta que el botón esté alineado con el agujero.
4.
Para ajustar el largo del Tubo Telescópico, presione el seguro de extensión hacia abajo. Mientras
tanto, mueva la sección superior del Tubo hasta el largo deseado (FIGURA 1-D). Suelte el seguro,
luego ajuste la sección superior del Tubo nuevamente hasta que haga clic y esté asegurada en su
lugar.
5.
Para desconectar el Tubo Telescópico, gire 180º el Gancho del Cable inferior hacia arriba y presione
firmemente el botón mientras hala el Tubo fuera de la yunta del Cabezal del Trapeador (FIGURA 1-E).
