background image

6

A

B

C

I

J

E

K

D

F

G

H

Figure 1 

DANGER

Grounded 

outlet 

Grounding Pin 

Plug 

PARTS DESCRIPTION

Electric Motor
The motor is used to power the pump. It is equipped with a thermal overload protector. If the motor 

overheats for any reason, the thermal overload protector will shut it down in order to prevent the motor 

from being damaged.
Air Compressor Pump
The pump compresses the air and discharges it into the tank via the piston that moves up and down in the 

cylinder.
Safety Valve
This valve is used to prevent the compressor from building too much pressure. If the pressure reaches the 

preset level of the motor, it will automatically pop open. You can also pull the ring on the valve to open 

manually.
ON/OFF Switch
This switch turns on the compressor and is operated manually.When in the ON position, it allows the 

compressor to start up or shut down automatically, without warning, upon air demand.ALWAYS set this 

switch to OFF when the compressor is not being used and before unplugging the compressor.
Air Pressure Regulator
The regulator is used to adjust the pressure inside the line to the tool that is being used. Turn the knob 

clockwise to increase the pressure and counter-clockwise to decrease the pressure.
Tank Pressure Gauge
The gauge measures the pressure level of the air that is stored in the tank. It cannot be adjusted by the 

operator and it does not indicate the pressure inside the line.
Outlet Pressure Gauge
The gauge measures the regulated outlet pressure.
Quick Coupler
The quick coupler is connected to a quick connector which is connecting to air hose.
Drain Valve
The drain valve is used to remove moisture from the air tank after the compressor is shut off.
Air Tank
The tank is where the compressed air is stored.
Power Cord
This product is for use on a nominal 120-volt circuit and should be grounded. A cord with a grounding plug 

as illustrated must be used. Make sure that the product is connected to an outlet that has the same 

configuration as the plug (see Figure 1). No adapter should be used with this product. Check with a 

licensed electrician if the grounding instructions are not understood or there is doubt as to whether the 

product is properly grounded. Do not modify the the plug provided. If it will not fit the outlet, have the 

proper outlet installed by a licensed electrician.

Improper installation of the grounding plug will result in a risk of 

electric shock. If repair or replacement of the cord or plug is 

necessary, do not connect the grounding wire to either flat blade 

terminal. The grounding wire is in the green outer surface.

Summary of Contents for 3300381
















Reviews: