background image

Q-Logic™ Setup

10.0

15

Tremor Suppression

10.4

The

Tremor Suppression

parameter sets a neutral range that suppresses possible tremors (trembling

of hand or drive surface conditions) on the joystick. Setting from 0% to 100%.

Follow

Steps 1 & 2

from

Section 10.2

Select

m: Tremor Suppression

option with the navigation's

Up & Down

buttons, then

press the

Right

button.

Use the

Plus & Minus

buttons to adjust the

Center Deadband

. To turn suppression

off, adjust the setting to 0%.

Press

Left

navigation button

to save.

NOTICE

When short command is used to operate the power chair,

the Tremor Suppression should not be set over 90%, otherwise

any short throw will be ignored.

Assign Direction Function

10.5

The Assign Direction function allows you to set the axis direction. For example, if you want to
change Forward (X axis 0 to 100) to Reverse (X axis 0 to -100) or Left (Y axis 0 to -100) to Right (Y 0
to 100). If you switch Forward to Reverse, the system will automatically change Reverse to Forward.
Same with Left and Right. Parameters are measured in percent (%).

Follow

Steps 1 & 2

from

Section 10.2

Select

Assign Direction

option with the navigation's

Up & Down

buttons, then press

the

Right

button.

Follow the on-screen instructions. When finished, press OK to save.

Summary of Contents for IDM-MULTI-9













































Reviews: