background image

1

Customer Satisfaction

Stealth Products

is committed to 100% customer satisfaction. Your complete

satisfaction is important to us. Please contact us with feedback or suggestions to
help us improve the quality and usability of our products.

You may reach us at:

Stealth Products, LLC

104 John Kelly Drive

Burnet, TX 78611

Phone: (512) 715-9995

Toll Free: (800) 965-9229

Fax: (512) 715-9954

Toll Free: (800) 806-1225

[email protected]

www.stealthproducts.com

MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany

General

Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse or failure to follow instructions will
void the warranty.
Immediately discontinue use if any function is compromised, if parts are missing
or loose, or if any component shows signs of excessive wear. Consult with your
supplier for repair, adjustment, or replacement.
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in the these instructions must be familiar with and understand all
safety aspects of the devices mentioned. In order for our products to be used
successfully, you must read and understand all instructions and warnings, and
maintain our products according to our instructions on care and maintenance.
The installation instructions will guide you through this product’s options and
possibilities.
Instructions are written with the expressed intent of use with standard
configurations.

They

also

contain

important

safety

and

maintenance

information, as well as describe possible problems that can arise during use. For
further assistance, or more advanced applications, please contact your supplier
or

Stealth Products

at (512) 715-9995 or toll free at (800) 965-9229.

Always keep the operating instructions in a safe place so they may be referenced
as necessary.
All information, pictures, illustrations, and specifications are based on the product
information that was available at the time of printing. Pictures and illustrations
shown in these instructions are representative examples and are not intended to
be exact depictions of the various parts of the product.

Summary of Contents for i2i













Reviews: