stayer MINI COM 12V, Operating Instructions Manual

Page: 14 / 28

ENGLISH
14
14
3. Instructions for putting into operation
3.1 Positioning
Keep working area clean and orderly. Disorderly and little
illuminated areas favor work accidents.
Do not use electric tools in potentially explosive
atmospheres or in the presence of inflammable liquids,
gases or powders. Electric tools cause sparks that may
ignite powders or smoke.
Keep children and other people away while using the
electric tool. Getting distracted may make you lose control
over the machine.
3.2 Assembling
Valve Adapter (FIG. 2)
•Push adapter 6 downwards onto the threaded section of
the valve rod or one of the three accessories delivered
together with the inflating device (fig. A2).
•When the adapter is positioned completely down on the
threads, press lever 6 with your finger downward so as to
fix it in its position (figure A3).
•To release the adapter 3, pull lever 6 upwards and pull
the adapter 3.
•Operate your inflating device only with the nozzles as
included or with standard valves for tires (figure A4).
Accessories
• Place the universal valve adaptor 3 over the stud of the
inflator needle or the conical nozzle.
• Press lever 6 of the universal valve adaptor downward
until it wedges into its position.
• Put inflator needle 10 or the conical nozzle into the object
that is to be inflated.
Remark:
The conical nozzles 9 and standard extension nozzles 11
and the inflator needle 10 shown in figure C are delivered
together with the compressor.
3.3 Illustrated description
1. Universal adapter sleeve air valve
2. Cord
3. Universal adapter for valves.
4. Gauge
5. Motor housing
6. Lever universal adapter
7. Switch on / off
8. 12V Plug
9. Standard nozzle
10. Needle for inflating
11. Nozzle extension
4. Operating instructions
4.1 Positioning and testing
To switch the compressor on, you must use the ON/OFF
switch 7 located at the upper portion of the compressor.
Connection to power supply:
Risk of unsafe operation
• Do not operate the compressor when the motor of the
automobile is running.
• Always completely extend the 12V DC cable 2 before
each use.
• To turn the compressor on, plug the 12V adapter into the
vehicle’s 12V socket for accessories, and press switch 7
towards red in position “I”.
To turn the compressor off, press switch 7 into position
“O”.
4.2 Setting operations:
Risk of explosion. Too much air pressure
causes risk of blasting. Check which is the
maximum pressure established by the
manufacturer of the articles that will be inflated.
• To operate the valve adapter 3, position the lever 6
upward and then penetrate the valve to inflate the object
adapter or floating (9-11) or balls (9) and close the lever 6
to seal the circuit (Figure A1-A4)
• To activate the compressor, connect the adapter to 12
volt accessory outlet 12 volt vehicle and press the red
switch to position “I”.
• If necessary, turn the key to start the car capable of
powering a contact.
• To turn off the compressor, press the 7 “O”.
REMARK: Let the lever 6 always in its upward position
when not in used.
Manómetro
This gauge located on the upper portion of the inflating
device, will provide you with a lecture in PSI (pounds per
square inch) and as well in kilo Pascal: kg/cm2 Newton
per square meter). In the case of vehicle tires, it is
recommended to control the pressure lecture with another
gauge for tires.
Problem Possible cause Possible solution
•The unit does
not start..
• adjusted pressure
may be below the ac-
tual pressure.
• fuse blown in the 12V
adapter.
• indicator is in contact
with the pressure need-
le.
• cable unplugged.
• automatic switch trig-
gered.
• switch or cable dama-
ged.
• replace adapter and cable.
• plug recharger into another
socket.
Servicing at a STAYER Ser-
vice Center o an authorized
service center.
RECOMMENDED OPERATING PRESSURES (see TABLE 1 –
page 8)