ENGLISH
15
15
4 Commissioning
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
Attaching the additional handle.
Always work with the additional handle
attached (4)! Secure the additional handle by
screwing it tightly to the left or right.
5 Use
5.1 On/Off switch, continuous activation
Always guide the machine with both hands.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits.
After switching off the machine, only place it
down when the motor has come to a standstill.
In continuous operation, the machinecontinues
running if it is forced out of your hands.
Therefore, always hold the machine using the
handles provided, stand in a safe position and
concentrate.
Switching on/Continuous activation:
Push sliding
switch (1) forward. For continuous activation, now tilt
downwards until it engages.
Switching off:
Press the rear end of the slide switch (1)
and release.
5.2 Setting belt speed
The belt speed can be preset via the setting wheel (2)and
is infinitely variable.
Positions 1-6 correspond approximately to the following
belt speeds:
1 ......... 2.7 m/s
4 ........6.3 m/s
2 ......... 3.8 m/s
5 ........7.6 m/s
3 ......... 5.1 m/s
6 ........8.5 m/s
5.3 Sanding belt replacement
- Release the tensioner arm (5) and remove the sanding
belt (6).
- Place the new sanding belt on the rollers such that
its direction of circulation (arrows on the inside of the
sanding belt) matches the arrow (7) on the gearbox.
- Release the tensioner arm (5).
- Ensure that the sanding belt is completely on the
rollers.
5.4 Sanding procedure
Place the machine on the material such that the sanding
belt is parallel to the surface of the workpiece.
When working, please ensure that the machine is operated
at right angles to the pipe so that the belt does not fall off
the rollers.
Using the additional handle, the belt can be pressed
against the pipe and at same time placed around it. The
angle of contact and the cutting output may be changed
by the contact pressure.
Keep the machine in constant motion because otherwise
recesses could be produced in the material.
6 Cleaning and Maintenance
Motor cleaning:
blow compressed air through the rear
ventilation slots of the machine regularly, frequently and
thoroughly. Here, the machine must be held firmly.
7 Accessories
Use only genuine STAYER accessories.
If you need any accessories, check with your dealer.
The dealer needs to know the exact model of your power
tool in order to select the correct accessory.
For a complete range of accessories, see
www.grupostayer.com or the main catalogue.
8. Maintenance and service instructions
8.1 Repair service
Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under:
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
8.2 Disposal and recycling
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/
UE/ for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.
1
Summary of Contents for LT1401EK
Page 3: ...ESPA OL 3 3 1 2 5 7 4 6 3...
Page 29: ...29 29 1 2 RCD RCD 3 4...
Page 30: ...30 30 www grupostayer com STAYER STAYER STAYER STAYER 1 2 FI FI 8 P2 30...
Page 37: ...NOTAS 37...
