STATESMAN GH60GB Instruction Manual Download Page 10

Page: 10 / 16

WARNING: Do not dismantle the Gas Tap Shaft: In the event of a malfunction, change the

whole tap.

• Before replacing the Flame Spreader and Burner Cap, ensure that the Injector is not blocked.

• A full operational test and a test for possible leaks must be carried out after a gas conversion.

• After completing conversion, the quailified gas engineer will need to mark “V” on the right gas

category to match with the setting on the rating plate. Remove the previous setting mark.

Control handle

Sealing ring

Tap

Important: For butane/propane gas, the adjusting screw must be tightly screwed in.

• Refit the control knobs to each Gas Tap.

• Test the flame by quickly turning the Control Knob from maximum to minimum, if the flame goes

out then you will need to make further adjustments to the gas flow.

• Repeat the process again until the gas flow is correct.

Adjustment of Minimum Level of the Flame

• Ignite the burner and set to MIN

• Remove the Control Knob and place a small bladed screwdriver in the centre of the Gas Tap

Shaft.

• Adjust until a steady flame is reached, about 3 – 4mm and does not extinguish when the Control

Knob is turned down to MIN.

• Repeat this procedure for all burners

Summary of Contents for GH60GB
















