background image

4

Do not turn off the water heater or
change the water temperature while
someone is bathing.

Be sure the gas/power supplied
matches the gas on the rating
plate.

Do not allow small children to play
unsupervised in the bathroom.
Do not allow small children to
bathe unsupervised.

Consult the nearest sales agent if
the water heater location needs to
be changed.

Contact a qualified service
technician for any necessary
repairs, service or maintenance.

Important Safety Information

-

2

Leave the proper clearance between
the water heater and nearby objects
(trees, timber, boxes with flammable
materials etc.).

Do not place or use a spray can
near the heater or the exhaust vent
terminal.

Left side:
Min. 2"

Right side:
Min. 2"

Min. 3" from
vent pipe

Do not place combustibles such as
laundry, newspapers, oils etc. near
the heater or the exhaust vent
terminal.

Exhaust vent
terminal  (indoor
installation)

*

Indicates suggested clearances for
maintenance.

Front:
Sug. 24"

*

[When installing indoors]
Check the air supply
vent for dust or
obstructions.

Do not use combustible chemicals
such as oil, gasoline, benzene etc.
in the vicinity of the heater or the
exhaust vent terminal.

Unit

(Continued)

Do not connect the water heater to
a solar water heater.

This can result in unreliable temperature
control, scalding or equipment failure.

For Natural Gas

Summary of Contents for Gas Water Heater




















































Reviews: