background image

8

REPAIR PARTS

REPAIR PARTS SCHEDULE

ORDERING REPAIR PARTS

The following parts may be ordered through the store you
purchased the tank from, or direct from the factory listed on the
model & rating plate located on the lower front of the tank.
Selling prices will be furnished on request or parts will be
shipped at prevailing prices and you will be billed accordingly.
When ordering repair parts always give the following
information:  (1) Part description, (2) Model serial number, (3)
Element wattage, (4) Voltage, (5) Part number.

WATER HEATER SOUNDS

1. T h e   t a n k   i s   e q u i p p e d   w i t h   a n   i m m e r s i o n   h e a t i n g

element for fastest recovery. If the  tank occasionally
makes noises this is not a defect or a safety hazard.

2. L i m e   o r   s c a l e   h a s   a c c u m u l a t e d   o n   t h e   h e a t i n g

element causing a hissing sound.  Element scale
removal can be accomplished by using vinegar or by
scraping.

ITEM

NO.

PART DESCRIPTION

1

Primary Anode

2

1” NPT Plastisert Nipple

3

Anode/Hotwater Outlet

4

Element Gasket

5

Element

6

Thermostat Bracket

7

Thermostat w/Hi Limit

8

Terminal Cover

9

Access Panel

10

Dip Tube

11

Dip Tube w/1” NPT Nipple

12

T & P Valve

13

3/4” NPT Plastisert Nipple

14

Indicator Light

15

Drain Valve

16

Access Panel

17

Plug

Summary of Contents for 198067-000









Reviews: