FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
FCC ID: Y3H706120181227
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC ID: 11232A-7061
IC Radiation Exposure Statement
This equipment complies with IC RSS-247 radiation exposure limit set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0.5cm
between the radiator and your body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to
www.startech.com/warranty
.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください
。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Notes:
The maximum distance between the transmitter and the receiver is 600 ft. If
the wireless signal is obstructed by walls, or other interference the signal quality and
maximum distance will likely be reduced.
When extending infrared, this product can only support an IR signal in the 38kHz
carrier frequency.
Mounting the Transmitter/Receiver
The
Transmitter/Receiver
can be mounted using the
Mounting Hardware
included.
1. Align the
Mounting Hardware
with the
Mounting Hole
on the back of the
Transmitter/Receiver
.
2. Screw the
Mounting Hardware
into the
Mounting Hole
, being careful not to
overtighten.
3. Loosen the
Adjustment Knob
on the
Mounting Hardware
.
4. Adjust the position the
Transmitter/Receiver
is facing.
5. Tighten the
Adjustment Knob
on the
Mouting Hardware
when the
Transmitter/
Receiver
is in the desired position.
LED Indicators
LED
Display
Function
HDMI
Transmitter
and
HDMI
Receiver
Network
Solid
Power is connected to the
Transmitter.
Slowly flashing red
Connecting to a
Device
.
Video
Solid
Video transmission active.
Slowing flashing blue No video signal input.
Network &
Video
Flashes
Indicates the Receiver is pairing.
Alternate flashing
(flash, pause, flash)
Channel switching in active.
Connecting the Extender
1. Position the
Wireless Transmitter
near the
Video Source Device
(e.g. Computer,
Blu-ray Player).
2. Connect an
HDMI Cable
(sold separately) to the
HDMI IN Port
on the
Wireless
Transmitter
and to the
Video Output Port
on the
Video Source Device
.
3. (Optional) Connect the
IR Blaster
to the
IR Out Port
on the
Wireless Transmitter
,
and position the
IR Blaster
directly in front of the IR sensor on your
Video Source
Device
.
Note:
Check the manual of your
Video Source Device
for the IR sensor location.
4. Connect the
Universal Power Adapter
to the
DC 5V Port
on the
Wireless
Transmitter
and to an
AC Electrical Outlet
.
5. Position the
Wireless Receiver
near your
Display Device
(e.g. Television, Projector).
6. Connect an
HDMI Cable
to the
HDMI Output Port
on the
Wireless Receiver
and to
an HDMI port on the
Display Device
.
7. (Optional) Connect the
IR Receiver
to the
IR In Port
on the
Wireless Receiver
, and
position the
IR Receiver
in the area you would like to point your IR controller.
8. Connect the
Universal Power Adapter
to the
DC 5V Port
on the
Wireless Receiver
and to an
AC Electrical Outlet
.
