Starmatrix Clever-Pool M/220V Installation, Operation & Maintanence Instructions Download Page 16 | Manualshive

Page: 16 / 18

Starmatrix Clever-Pool M/220V Installation, Operation & Maintanence Instructions Download Page 16

Press the SET/RESET button to step to SPEED setting. The display will now show the flashing four digits for speed,which is
the speed for AUTO MODE 1.Press the up or down button to change motor speed. Alternatively press one of the systems
preset speed buttons LOW RPM, MEDI RPM, HIGH RPM.

Press the SET/RESET button to store the speed and step over to AUTO MODE 2. The display should show CURRENT
TIME, START TIME, STOP TIME and the stored time with hours digits flashing. This is the start time for AUTO MODE 2.

Repeat steps above to set speed, start and stop times for AUTO MODE 2 3 and 4. Pressing the SET/RESET button
after selecting the speed for Auto mode 4 will finalize the timer settings.

The display will go blank and return to stop mode with the current set time displayed.

- 16 -

«
...
14
15
16
17
18
»

Summary of Contents for Clever-Pool M/220V



















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands