background image

Part Number: 4530 

 Page 5 

Version 1.5 

© 2015 Starkey Products, Inc.  

 
 
Final Installation: 

1.

 

Double check everything to make sure it was connected properly. Test the Light Bar to make sure 
it comes on and off with your other running lights. This can be done by unlocking/ locking the 
doors with your key fob. If the lights do not come on, visit the trouble shooting guide below.  

2.

 

Make sure that all of the hardware you removed from the grille/ active shutters has been re-
installed.  

3.

 

Re-install the head light trim panels by reversing the removal procedure you completed earlier. Be 
sure they are completely snapped back into place and all corners line up properly.   

4.

 

Re-install the radiator cover and make sure all push-pins are re-installed. Failure to do so can 
cause check engine light to illuminate on your dash.  

5.

 

Enjoy your new Raptor-Style Light Bar! The lights will activate automatically when your running 
lights are turned on.  

 
 
Trouble shooting guide: 
Lamps won’t turn on –  

 

Check to make sure you connected 

red

 wire tap to the correct wire outlined in the ‘Installing the 

Light Bar’ section above. This is the MOST common mistake made during installation. 

 

Check the ground cable you connected under the ‘Installing the Light Bar’ section. Make sure that 
it is making proper contact and that the bolt is tightened.  

 
If you are still having trouble with your product, please contact us for technical assistance. Tech support is 
available via phone Monday through Friday 9am-5pm. Email tech support is available during regular 
business hours as well as weekends, holidays, and evenings. 
 

Starkey Products, Inc. 
Phone:

 (386) 951-6335 

Email:

 

[email protected]

 

Website:

 

www.Starkey-Products.com

 

 

Limited Warranty: 

This warranty covers defects in materials or workmanship in any component sold by Starkey Products, Inc. or its authorized 
dealers. Warranty is effective for five years from the date of purchase*. Coverage terminates if you sell or transfer ownership 
of the product. Starkey Products will repair or replace the defective or malfunctioning product or any defective or 
malfunctioning part thereof at no charge. This warranty covers parts and labor only. This warranty does not cover any 
problem that is caused by abuse, misuse, acts of God, or improper installation. Any modification or alteration to any 
component will void the product warranty. Warranty does not cover wear that any components receive through the normal 
course of operation and use (including but not limited to bulbs). All warranty claims require proof of purchase. 
 
*Any painted surfaces are guaranteed not to bubble, peel, or crack for the duration of the warranty period. Warranty does not 
cover normal wear and tear resulting from impacts, scratches, road debris, or harsh chemicals.   

Summary of Contents for 4530






Reviews: