Starizona MicroTouch Autofocuser Operating Instructions Manual Download Page 6 | Manualshive

Page: 6 / 12

background image

Installing the MicroTouch and FocusMax Software

Load the included CD.  On the CD will be two installation files, one for the MicroTouch
software  and  one  for  FocusMax.    The  MicroTouch  software  installation  file  is  called
Setup.  Open this file and follow the directions given to install the MicroTouch software.
The  program  will  be  located  in  the  Windows  Start  Menu  under

All Programs >

Starizona > MicroTouch > MicroTouch

.

Open the FocusMax installer and follow the directions given to install the FocusMax
software. The program will be located in the Windows Start Menu under

All Programs

> FocusMax

.

Installing the MicroTouch Hardware Drivers

Connect the included USB cable to the hand control then to the computer. The

Found

New Hardware Wizard

should appear. Select the automatic install routine. The wizard

should find the included drivers and successfully install the hardware.

If, for some reason, Windows cannot automatically install the hardware, you can run the
hardware installer again and manually select the driver. The driver is located in the

Program Files > Starizona > USB2Driver

folder and is called SiUSBXp.sys.

«
...
4
5
6
7
8
...
»

Summary of Contents for MicroTouch Autofocuser













Reviews:

No comments

Related manuals for MicroTouch Autofocuser

Brand: Calumet Pages: 4

Brand: Acdeos Pages: 38

AdvancedPunch Pro

Brand: GBC Pages: 92

Brand: i-onik Pages: 6

Brand: PASCO Pages: 6

Brand: PASCO Pages: 4

CK 3000 Evolution

Brand: Parrot Pages: 2

Brand: quadient Pages: 2

AcousticDesign AD-S52

Brand: QSC Pages: 4

Brand: Tait Pages: 46

Brand: Tait Pages: 9

Brand: Tait Pages: 89

Brand: Tait Pages: 20

Brand: NEEWER Pages: 58

Reference Series

Brand: OEM Audio Pages: 29

Brand: XCM Pages: 11

Brand: BabySense Pages: 76

Brand: hepco & becker Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands