Starbridge Networks Lynx L-525 User Manual Download

Page: 5 / 56

Starbridge Networks
Lynx L-525 4 Port and Wireless Modem

Page 5 of 56

Front Panel View

LED

Mode

Indication

Solid Wireless

enabled.

No light

Wireless is disabled.

Wireless

Blinking

There is wireless traffic.

Solid

ADSL is connected.

No light

ADSL is not connected. The ALARM led
will be red.

DSL

Blinking

The Lynx L-525 is connected to ADSL.

Solid

An IP Address has been obtained
dynamically from the broadband network

No light

No IP address was obtained. For static IP
this will not light.

Internet

Quick blinking

Traffic is passing.

Solid

Lynx L-525 is connected to the LAN.

No light

No connection to the LAN. Check if the
LAN cable is connected to the Lynx L-525.

Ethernet 1-4

Blinking LAN

traffic

Solid (red)

An Alarm condition has occurred.

Alarm

No light

Normal operation

Solid

Lynx L-525 is powered on.

Power

No light

Lynx L-525 is not powered. Check if the
Lynx L-525 is plugged in and if the power
switch is turned on.

Summary of Contents for Lynx L-525

























































Search results

Summary of Contents for Lynx L-525

Reviews:

Related manuals for Lynx L-525

Brands by name

Popular brands

Starbridge Networks Lynx L-525, User Manual

Search results

Summary of Contents for Lynx L-525

Reviews:

Related manuals for Lynx L-525

Brands by name

Popular brands