■
Verify that all parts listed above are included in your shipment.
Take time now to enter your
INSTINCT LEG EXTENSION / LEG CURL
serial number in the space below. If parts are miss-
ing, or if you have any operational questions, please call Star Trac’s Service department at (800) 503-1221; have your serial num-
ber ready.
Serial No. __________________________________________
ASSEMBLY
1.
Assemble the Main Frame to the Weight Frame
Align the two drilled holes in the lower cross-
beam (3) with the mating holes in the bottom
of the weight stack frame (1). Secure the cross-
beam to the weight frame using two screws
(82), four washers (88), and two lock nuts (85).
Tighten the nuts securely.
Align the two drilled holes in the upper cross-
beam (4) with the mating holes in the side
beam of the weight stack frame (1). Secure the
crossbeam to the weight frame using two
screws (82), four washers (88), and two lock
nuts (85). Tighten the nuts securely.
Position the main frame (2) so the two drilled
holes in the lower crossbeam (3) and the two
drilled holes in the upper crossbeam (4) are
aligned with the mating holes in the main
frame.
Secure the main frame to the lower crossbeam
using two screws (78), one spring washer (89),
four washers (88), and two lock nuts (85).
Tighten the nuts securely.
Secure the main frame to the upper crossbeam
using two screws (82), four washers (88), and
two lock nuts (85). Tighten the nuts securely.
2.
Install the Leverage Arm
NOTE:
Two people are required to install the
leverage arm; one to hold the leverage arm in
position, and one to install the leverage arm shaft.
Loosen the two setscrews (67) in each leverage
arm shaft support bearing in the weight stack
frame (1).
Slide the leverage arm shaft (32) through the front
support bearing in the weight stack frame (1) until
the shaft extends midway between both support
bearings in the weight stack frame (1). Slide the
leverage arm (14) onto the leverage arm shaft.
Slide the leverage arm shaft (32) back toward
the rear support bearing in the weight stack
frame, and install the following items on the
shaft, one at a time:
■
Washer (41)
■
Flywheel Stop Arm (12)
■
Washer (41)
■
Range-of-Motion Flywheel (11)
ASSEMBLY
1.
Assemble the Main Frame to the Weight Frame
Align the two drilled holes in the lower cross-
beam (3) with the mating holes in the bottom
of the weight stack frame (1). Secure the
crossbeam to the weight frame using two
screws (60), four washers (66), and two lock
nuts (63). Tighten the nuts securely.
Align the two drilled holes in the upper cross-
beam (4) with the mating holes in the side
beam of the weight stack frame (1). Secure the
crossbeam to the weight frame using two
screws (60), four washers (66), and two lock
nuts (63). Tighten the nuts securely.
Position the main frame (2) so the two drilled
holes in the lower crossbeam (3) and the two
drilled holes in the upper crossbeam (4) are
aligned with the mating holes in the main frame.
Secure the main frame to the lower crossbeam
using two screws (57), one spring washer (67),
four washers (66), and two lock nuts (63).
Tighten the nuts securely.
Secure the main frame to the upper crossbeam
using two screws (60), four washers (66), and
two lock nuts (63). Tighten the nuts securely.
2.
Install the Leverage Arm
NOTE:
If desired, install the alternate range-
of-motion limiter at this time (see “Installing
the Alternate End-of-Travel Limiter” on page
20 for details).
NOTE:
Two people are required to install the
leverage arm; one to hold the leverage arm in
position, and one to install the leverage arm shaft.
Loosen the two setscrews (48) in each leverage
arm shaft support bearing in the weight stack
frame (1).
Hold the leverage arm (10) in place between
the two shaft support bearings in the weight
stack frame (1).
Insert the leverage arm shaft (22) through the
leverage arm and both support bearings.
Secure the leverage arm shaft (22) to the
weight stack frame (1) using two screws (52)
and end caps (24).
Tighten the two setscrews (48) in each lever-
age arm shaft support bearing in the weight
stack frame (1).
NOTE:
Two people are required to install the leverage arm actuator; one to hold the actuator in position, and one to install
the actuator shaft.
Hold the leverage arm actuator (9) in place on the leverage arm (10) with the mounting flanges of the actuator positioned
around the shaft guide on the leverage arm.
Insert the leverage arm actuator shaft (18) through the leverage arm and both actuator mounting flanges.
Secure the leverage arm actuator shaft (18) to the leverage arm (10) using two screws (52) and end caps (24). Tighten the
screws securely.
STAR TRAC INSTINCT LEG MACHINES O
WNER
’
S
M
ANUAL
15
22
STAR TRAC INSTINCT LEG MACHINES O
WNER
’
S
M
ANUAL
66
67
57
57
66
66
66
60
60
2
3
66
66
66
66
66
66
66
66
66
66
63
63
63
63
63
63
63
66
4
60
60
60
60
1
9
52
24
18
10
24
52
24
52
48
48
48
RANGE-OF-MOTION
LIMITER
22
24
52
1
88
88
88
88
88
88
88
88
88
88
88
88
88
88
88
89
78
78
82
82
2
3
4
85
85
85
85
85
85
85
82
82
82
82
1
15
72
34
63
10
72
35
14
35
72
72 35
28
41
12
41
11
32
35
72
67
1
67
67