Star Trac E-TBT Installation Manual Download | Manualshive

Page: 42 / 53

background image

43

620-7921 Rev A

Step 22.

Connect the seven-pin interface cable from the
console to J14 connector on the display board.

Step 23.

Now connect the iPod® cable from the bottom
cover to J10 connector on the center console
board.

Step 24.

Next replace the bottom cover. Use the screws
saved from the earlier step to secure the display
bottom. Tighten the screws so they are snug,
then plug in the CSAFE power cable to the back
of the display.

Note:

Take special care to not pinch any of the ca-

bles between the plastics.

Step 21.

Connect the center console keypad cable to J8
connector on the display board.

«
...
40
41
42
43
44
...
»

Summary of Contents for E-TBT






















































Reviews:

No comments

Related manuals for E-TBT

Brand: Weslo Pages: 16

Brand: NordicTrack Pages: 36

Brand: Stamina Pages: 23

Brand: Infiniti Direct Pages: 22

Brand: SPORTSTECH Pages: 141

Brand: SportsArt Fitness Pages: 5

"No Start" 8007

Brand: SportsArt Fitness Pages: 8

Brand: Sportop Pages: 18

Brand: Sportop Pages: 24

Brand: Sportplus Pages: 116

XP StrideClimber 600

Brand: ProForm Pages: 16

CardioCross Trainer 700

Brand: ProForm Pages: 24

910 E Elliptical

Brand: ProForm Pages: 40

Brand: ProForm Pages: 28

800 PFEL57907.0

Brand: ProForm Pages: 24

650 Cardio Cross Trainer Elliptical

Brand: ProForm Pages: 33

Brand: ProForm Pages: 24

600 N Elliptical

Brand: ProForm Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands