background image

28 

 

 

620-7921 Rev A 

 

ATTENTION 

• 

Star Trac recommends that the Total Body Trainers be spaced a minimum of 20.0 inches (0.5 
m)  apart  to  allow  safe  and  easy  ingress  and  egress.  Even  more  importantly,  there  must  be  at 
least 48 inches (1.25 m) of free space behind the Total Body Trainer. 

 

• 

As with any motorized equipment, the area where Total Body Trainers are located must be free 
of  obstructions  and fixtures  with  sharp  edges  to prevent  injury  in  the  event  that a  user  trips  or 
loses balance and falls. 

 

Use the checklist below to ensure the proper installation of the Total Body Trainer: 

 

1.  All parts, tools and hardware in the package are accounted for. 
2.  Center console assembly is properly mounted and secured. 
3.  All screws are tightened and torqued down to their specified values. 
4.  Display’s mounting bracket  and back cover are properly mounted and secured. 
5.  All cables and harnesses are properly plugged to their respective connectors. 
6.  The front and back display plastics are properly installed and secured. 
7. 

Verify iPod menu is functioning and user can browse and listen to music.

 

8.  Verify clear audio coming from both earphones. 

For technical assistance call Star Trac Customer Service: 1 800 503 1221 

Summary of Contents for E-TBT






















































Reviews: