Star Trac E-TBT Installation Manual Download | Manualshive

Page: 14 / 53

background image

15

620-7921 Rev A

Step 15.

Next plug in the coax cable to the coax adapter
on the tuner card of the embedded display as-
sembly.

Step 16.

Now plug in the DC power cable from the base
neck to DC connectors on the embedded dis-
play assembly.

Step 14.

Plug-in the 12-pin main I/O cable from the neck
to the 12 pin connector on the FitCPU board of
the embedded display assembly.

Step 13.

Plug-in the heart rate cable from the neck into
the heart rate board connector on the FitCPU
board of the embedded display assembly.

«
...
12
13
14
15
16
...
»

Summary of Contents for E-TBT






















































Reviews:

No comments

Related manuals for E-TBT

NordicTrack STUDIO ELLIPTICAL

Brand: ICON Health & Fitness Pages: 36

Brand: CAPITAL SPORTS Pages: 186

Brand: Nautilus Pages: 84

Brand: JOHNSON HEALTH TECH. Pages: 15

Brand: V-fit Pages: 24

Brand: SOLE Pages: 11

PRO-FORM ENDURANCE 1120 E

Brand: ICON Pages: 32

Brand: Landice Pages: 56

Fitness Cycle E3100

Brand: Vision Fitness Pages: 39

Brand: U.N.O Pages: 20

Resolute RSL 618

Brand: Precor Pages: 12

HANDBOEK EFX 556i

Brand: Precor Pages: 2

Brand: Domyos Pages: 16

Brand: Precor Pages: 74

Brand: Tecnovita Pages: 38

CHRONO LINE ERX500

Brand: TOORX Pages: 18

Brand: Sports Authority Pages: 16

Brand: Sports Art Industrial Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands