Star Micronics LC-8521 Technical Manual Download Page 52

Page: 52 / 124

– 48 –

15. Platen Assy

(1)

Remove
Paper guide unit as described in section 14.
• Stop ring

[1]

• Adjust lever holder

[2]

(2)

Move the adjust lever outward.

(3)

Remove
• Ground spring

[4]

• Three stop rings

[5]

• Gear

[6]

• Bushing

[7]

• Wave washer

[8]

• Plain washer

[9]

• Platen Assy

[10]

[7]

[5]

[4]

[6]

[5]

[8]

[9]

[1] [2]

[3]

14. Paper Guide Unit

(1)

Remove
Roller angle unit as described in section 11.
• Paper feed roller unit as described in section 13.
• Screw

[1]

• Detector cover

[2]

• Gear

[3]

• Seventeen screws

[4]

• Rom cover

[5]

• Paper guide unit

[6]

Note:

Gear

[3]

should not be used again once they have

been removed . Always use new ones.

[4]

[2]

[1]

[6]

[4]

[3]

[5]

Summary of Contents for LC-8521





























































































































Search results

Summary of Contents for LC-8521

Reviews:

Related manuals for LC-8521

Brands by name

Popular brands

Star Micronics LC-8521, Technical Manual

Search results

Summary of Contents for LC-8521

Reviews:

Related manuals for LC-8521

Brands by name

Popular brands