Star Micronics LC-8521 Technical Manual Download Page 36

Page: 36 / 124

– 32 –

(6)

Release lever position detector
The leaf switch is open when the release lever is in the friction position, and is closed in the tractor position.

Detecting

signal

+5V

Leaf switch

Out put (V)

Rear SW

Out put (V)

Front SW

Paper feeding

method

Tractor (Front)

Friction

Tractor (Rear)

(7)

Adjust lever position detector
When the Adjust lever is set to or below position "3", the leaf switch becomes ON, as the Adjust lever is at "4" or
above, the leaf switch comes to OFF.

Detecting

signal

+5V

Leaf switch

Fig. 2-15 Release lever position detector

Fig. 2-17 Adjust lever position circuit

Control Method

Adjust lever position

Out put (V)

Print method

0~3

Normal mode

4~8

Multi-part mode

Fig. 2-16 Adjust lever position

Summary of Contents for LC-8521





























































































































Search results

Summary of Contents for LC-8521

Reviews:

Related manuals for LC-8521

Brands by name

Popular brands

Star Micronics LC-8521, Technical Manual

Search results

Summary of Contents for LC-8521

Reviews:

Related manuals for LC-8521

Brands by name

Popular brands