-3-
Electrical Connections
**Standby current < 0.001A
Left Arrow
Both=Center-Out
Right Arrow
Use standard On/Off switches rated for 5 amps and make your connections
according to the wiring diagram below.
Note: The wires are shown above in order of Priority. Higher priority wires will
override the patterns on any lower priority wires for the heads that are
enabled.
HIGHEST PRIORITY
LOWEST PRIORITY
Pink > White w/Brown > Green w/Yellow > Orange w/Red > Yellow
(Please note that PINK will become the lowest priority if you reprogram it for Low Priority Cruise Mode)
Default Wiring Setup
10 AMP Fuse
Ignition-Switched Relay
12VDC BATTERY
The RED wire must be connected to +12VDC
for any of the functions to work.
This wiring diagram below applies to the default programming of this light. There
are several additional advanced features that, if programmed, may affect the wire
functions shown. Most applications will not require any reprogramming, but you
can find these options described in detail under the
Advanced Programming
section.
Function
Wires
Function
Wires
ORANGE w/RED
- Warn 1
(Full Arrowstick Flash)
WHITE w/BROWN
- Left Arrow
GREEN w/YELLOW
- Right Arrow
RED w/GREEN
- Pattern Select
BLACK
- Ground
YELLOW
- Warn 2
(Arrow Tips Flash)
PINK
- Dim
(Reduces brightness to 15%)
[OPTIONAL CRUISE]
RED
- Power
-4-
Optional Advanced Programming
Programming is optional. If the default settings are acceptable, skip this section.
Programmable features include the following:
•
Pattern Selection
(both WARN and Traffic Directing Patterns)
•
Head Enable
(which heads activate)
•
Phase Selection
(which heads alternate from one another)
•
Dim
Settings
•
Cruise Mode
(Steady Burn)
Pattern Selection
•
Full Warn
(ORANGE w/RED)
•
Arrow Tips Warn
(YELLOW)
•
Traffic Directing Patterns (L, R, and C-O)
(GREEN w/YELLOW, WHITE w/BROWN, or Both)
1. Connect the RED wire to power and the
BLACK wire to Ground.
2. Activate the function you wish to program by
connecting the corresponding wire to +12VDC.
3. Touch and release the Pattern Select wire to
+12VDC to scroll through the patterns shown to
the right.
(Traffic Director L, C-O, R shown
below.)
Note: At any time you can shortcut to the
patterns with the asterisks by holding the
pattern select wire to +12VDC for the indicated
time.
4. Repeat for each function you wish to program.
Warn Patterns
1 Flicker
*
†
(factory default)
2 Slow Singleflash
†
3 Fast Singleflash
4 Slow Doubleflash
†
5 Medium Doubleflash
†
6 Slow Tripleflash
†
7 Fast Tripleflash
†
8 Quadflash
†
9 Quintflash
†
10 Tripleflash w/Post Pop
†
11 Quadflash w/Post Pop
†
12 Quintflash w/Pre Pop
†
13 Fast Doubleflash
†
14 Fast Quadflash
†
15 Singleflash Flicker
**
16 Doubleflash Flicker
17 Single, Quad w/Post Pop, Flicker
18 Delta-Omega
19 Random 1
20 Random 2
21 Random 3
***
22 Flashing Bounce
23 Full Bounce
24 Split Bounce
25 Half Bounce
26 Bounce w/End Pop
27 Search Lights
28 Eyeballz
29 Fade Invert
30 Moving Out
31 Triple In/Triple Out
32 Two Speed
33 Random 4
34 Delta X
* Shortcut Pattern #1 (3 sec/1 flash)
** Shortcut Pattern #2 (6 sec/2 flashes)
*** Shortcut Pattern #3 (9 sec/3 flashes)
†
SAE Approved Pattern
Patterns for Traffic Director
(8– and 6-Head Only)
Left, Right, and Center Out functions
all use the same pattern
1 Standard
*
2 6-Head TD with End Flash
3 Standard w/End Blink
4 Two-Head Traveling
5 Fast
**
†
6 Ultra-Fast
†
7 Four Head Traveling
†
8 Snake
†
9 Snake Pop
10 Pop
11 Marquee
12 Singleflash
†
***
(factory default)
13 Doubleflash
†
14 Quadflash
†
15 Single/Double/Quad Combo
* Shortcut to Pattern #1 (3 sec/1 flash)
** Shortcut to Pattern #5 (6 sec/2 flashes)
*** Shortcut to Pattern #12 (9 sec/3 flashes)
†
SAE Approved Pattern
