background image

8

9

IMPORTANT

 FUEL - ONLY USE UNLEADED 91 PETROL (ULP - 91RON) - NO ETHANOL 

Fuel tank capacity – 1.2 litres (1.2 L)

Use of incorrect fuel and/or oil may damage the pressure washer and will not be covered under warranty. 
Do not use E10 or any type of ethanol fuel as this will damage the pressure washer and will not be covered under 

warranty.
Do not use high octane fuels (greater than 91%) as this will damage the pressure washer and will not be covered 

under warranty.
•  Ensure you use clean fresh unleaded petrol (ULP) - No Ethanol.
•  Use a clean approved container to store your unleaded petrol (ULP) in before decanting into the fuel tank.
•  If contaminated (dirty) or old (stale) fuel is used, any damage caused will not be covered under warranty.

 OIL (CHECK DAILY - ONLY USE 4 STROKE MOTOR OIL)

To operate, this pressure washer requires oil in the sump, not supplied.  If the pressure washer does not have 

the correct level of oil in the sump, it will not run, see note below.
Oil capacity – approximately five hundred millilitres (0.5 L or 500 mL)
Oil type – SAE 30W or SAE 15W-40
•  Always check oil level before using.
•  Always use fresh clean oil.
•  Change oil every 50 hours or every 3 months. 
•  If contaminated (dirty) or old (stale) oil is used, any damage caused will not be covered under warranty.
NOTE: This pressure washer is fitted with an oil cut out switch. If the oil level is empty or low, then the pressure 

washer WILL NOT start or run.
Always check the oil level before starting the pressure washer.
Never check or add oil while the pressure washer is running.

Summary of Contents for SXPW2621

























Reviews: