background image

4

5

LUBRICATION OF ENGINE

Your engine comes with NO oil in the sump. You will need 

to add engine oil, refer to pages 9 and 14 for complete 

details and images. Failure to do this may result in damage 

to the engine, pressure washer and / or injury to the user.

ASSEMBLY

This pressure washer MUST be fully assembled by you prior 

to use.  Failure to do so will result in the warranty being 

VOID.  Failure to fully assemble this pressure washer may 

also result in personal injury.

SAFETY

Before attempting to operate this pressure washer the 

following basic safety precautions should be taken to 

reduce the risk of fire, electric shock and personal injury.  

It is important to read the instruction manual and to 

understand applications, limitations and potential hazards 

associated with this pressure washer.  It is important that 

you read, understand and follow these instructions very 

carefully. This pressure washer is not intended for use 

by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and 

knowledge, unless they have been given supervision or 

instruction concerning the use of the appliance by a person 

responsible for their safety.

BEWARE OF CHILDREN & PETS

Children and pets should be kept out of the operating 

area.  Children should not be allowed to touch or operate 

pressure washers.  All pressure washers should be kept out 

of reach of children.  When NOT in use keep the pressure 

washer preferably stored or locked in a secure well 

ventilated cabinet or room with the fuel tank empty.  

 
FUEL - UNLEADED 91 PETROL  
(NO ETHANOL)

Fuel used in this pressure washer is poisonous.  Always 

wear approved breathing protection when decanting 

fuel.  If you get any fuel on your skin or clothes wash the 

affected area immediately with soap and water and change 

your clothes.  If you get fuel in your eyes wash immediately 

with clean water and seek medical attention.  If any fuel 

is swallowed DO NOT induce vomiting, seek immediate 

medical attention.

WORK AREA

Work areas and benches should be kept tidy. Cluttered 

benches and work areas can cause accidents. Floors should 

be kept clean and free from rubbish. Special care should 

be taken when the floor is slippery due to sawdust or wax. 

Always leave sufficient distance, at least 5 metres between 

the pressure washer and the work area, especially when 

using tools designed for sanding or spraying liquids. As this 

pressure washer uses a petrol engine, only run the pressure 

washer outdoors or in a well ventilated area. If needed use 

a longer air hose to reach your work area.

 
OPERATING ENVIRONMENT

ALWAYS use your pressure washer in an open well 

ventilated area.  Do not expose your pressure washer 

to rain.  Do not expose your pressure washer to direct 

sunlight.  Keep the work area well lit.  Do not use your 

pressure washer in areas where there is a risk of explosion 

or fire from combustible materials, flammable liquids, 

paint, varnish, petrol, etc flammable gases and dust of an 

explosive nature.  As a precaution it is recommended that 

you consult an expert on selecting and using a suitable fire 

extinguisher and have it available for use in an emergency 

when operating the pressure washer.

SELECT A PRESSURE WASHER WITH A 
SUFFICIENT RATING

Select the right pressure washer for the job.  Do not use a 

pressure washer to do a job for which it was not designed.  

Do not force a small pressure washer to do the job of 

a heavy duty pressure washer.  Any damage caused by 

overloading will void the warranty.  Do not use pressure 

washers for purposes not intended.

 
HOT COMPONENTS

Beware many of the components will get hot during use.  

Never touch any of the metal pipes, pump or motor as 

these may burn. In particular ensure that the high pressure 

hose does not touch the hot muffler during use or when 

storing as it will damage the high pressure hose and this 

will not be covered under warranty.

Summary of Contents for SXPW2621

























Reviews: