background image

2

3

INTRODUCTION

Dear Customer,
Thank you for purchasing this pressure washer which has 

passed through our extensive quality assurance processes. 

Every care has been taken to ensure that it reaches you 

in perfect condition. However, in the unlikely event that 

you should experience a problem, or if you require any 

assistance, please do not hesitate to contact us;

If you have a problem, call customer service 
do not return this pressure washer to the 
place of purchase.

NOTE:

 For convenience we suggest taking a photocopy of 

your purchase receipt as the original may fade

CUSTOMER SERVICE

Australia: 1300 660 457
New Zealand: 0800 474 876
Operating times: Monday – Friday | 8.00am - 5.00pm

Australian Eastern Standard Time (AEST)

Due to continual product development, the product 

you purchase may differ slightly from the one  

shown here.

EXPRESS WARRANTY STATEMENT - 
PRESSURE WASHER

You are not required to do anything to register your 

pressure washer purchase.  Please attach the purchase 

receipt to this manual and ensure both are kept safe.  We 

hope you enjoy your new pressure washer, and if you have 

any problems call customer service on the above phone 

numbers.  Do not return to place of purchase.
Smart Marketing Group Pty Ltd (SMG) warrants that this 

pressure washer will be free from manufacturing faults 

or defects for 24 months, Domestic Use or 12 months, 

Commercial Use,  from the date of purchase, providing 

original purchase receipt is kept and shown when needed 

and is subject to the terms and conditions below.
If a warranty fault appears within the warranty period, 

SMG reserves the right to replace or repair the product. 

In the event that SMG chooses to replace the product, 

this original warranty will expire at the original date of 

purchase. If the product includes various accessories or 

components, only the defective accessory or component 

will be replaced or repaired.
SMG reserves the right to replace defective parts of the 

product with parts and components of similar quality, 

grade and composition where an identical part or 

component is not available.
Products presented for repair may be replaced by 

refurbished products of the same type rather than  

being repaired.  Refurbished parts may be used to  

repair the products.

What is covered.

•  Manufacturing fault or defect.

How to claim under this warranty.

•   Call customer service.
•   Ensure you have the following: Original purchase receipt, 

Model of pressure washer, Serial number of  

pressure washer.

•   Discuss the issue.
•   Customer service will advise which authorised service 

agent to take the pressure washer to provided the issue  

is a warranty one.

•   Take pressure washer to authorised service agent   

for repair.

What is not covered.

•   Use of Pressure Washer for hire.
•   Damage due to running dry or caused by dirty water.
•  Damage caused by incorrect oil
•   Damage caused by incorrect fuel or use of E10  

ethanol fuel.

•   Damage or deterioration due to transport.
•   Damage caused by negligence, misuse, abuse or accident 

or incorrect voltage and wattage.

•   Any corrosion or rusting.
•   Damage caused by incorrect set up and start up.
•   Replacement parts due to general wear and tear.
•   Pressure washers with serial number defacement, 

modification or removal.

•   Pressure washers which have been serviced by other than 

an authorised SMG service agent.

•   Pressure washers with no original purchase receipt.
•   Pressure washers which have been on sold,  

not original purchaser.

•   Damage due to non-servicing of pressure washer as is 

required by this manual.

•   Blockages / damage caused by dust, dirt, spiders webs  

or insects.

•   Damage caused by the incorrect fitting of accessories.
•   Damage caused by overloading, overworking  

the pressure washer.

•   Damage to attached equipment or third  

party accessories.

•   Damage caused by attached equipment or  

third party accessories.

•  Loan unit whilst warranty servicing is carried out.
•  Loss of income due to warranty servicing.

CONTACT DETAILS

Smart Marketing Group Pty Ltd

33-35 Lionel Road, Mt. Waverley

Victoria 3149, Australia.

Tel (+613) 9543 7266

Fax (+613) 9543 9839

[email protected]

Summary of Contents for SXPW2621

























Reviews: