(Original instructions)
ENGLISH
7
Using an Extension Cable
If it is necessary to use an extension cable, please used an
approved extension cable that fits the tool’s power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Features
This tool includes some or all of the following features.
1. ON/OFF Switch (Fig. A)
2. Spindle Lock (Fig. A)
3. Guard (Fig. A)
11. Variable Speed Dial (Fig. F)
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid an
initial jerk when starting. This feature is particularly useful
when working in confined spaces.
No-Volt
The No-volt function stops the grinder restarting without the
switch being cycled if there is a break in the power supply.
Assembly
WARNING!
To prevent accidental operation, turn off and
unplug tool before performing the following operations. Failure
to do this could result in serious personal injury.
Attaching and Removing the Wheel Guard (Fig. B)
WARNING!
To minimize the danger of serious personal injury,
please switch off the tool power and disconnect all plugs
before adjusting or removing/installing any accessory. Before
reassembling the tool, press and release the trigger switch to
make sure the tool is already switched off.
Attaching the Guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (3) collar over the groove (9)
of the gear housing.
3. Turn the guard (3) counterclockwise by 150 degrees.
4. Make sure that the screws (10) are tightened.
Removing the Guard
1. Loosen the screws (10) on the guard collar.
2. Pull up the guard (3).
WARNING!
Do not operate the tool when the safety guard is
not in place.
Note:
Refer to the grinding accessories chart at the end of this
section for accessories that can be used together with this
angle grinder.
Attaching and Removing Grinding Wheels (Fig. C
and D)
WARNING!
Do not use damaged grinding wheels.
1. Place the tool on a work bench, groove facing up.
2. Figure C: Attach the inner flange (4) correctly on the
output shaft (5).
3. Place the grinding wheel (6) on the inner flange (4).When
attaching a grinding wheel with a raised center,make sure
that the raised center (7) faces the innerflange (4).
4. Figure D: Tighten the outer flange (h) until the output shaft
(5).
4). When attaching the grinding wheel, the ring on top ofthe
outer flange (8) must face the wheel.
5. Press the spindle lock (2) and prevent the spindle (4)from
rotating until it locks in place.
6. Use the pin spanner to tighten the outer flange (8).
Preparation Before Use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
Cable cross-sectional
area (mm
2
) Cable rated
current (Ampere)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
15
25
30
45
60
Voltage
Amperes
Cable rated current (Ampere)
110-127
0 - 2.0
6
6
6
6
6
10
2.1 - 3.4
6
6
6
6
15
15
3.5 - 5.0
6
6
10
15
20
20
5.1 - 7.0
10
10
15
20
20
25
7.1 - 12.0
15
15
20
25
25
-
12.1 - 20.0
20
20
25
-
-
-
220-240
0 - 2.0
6
6
6
6
6
6
2.1 - 3.4
6
6
6
6
6
6
3.5 - 5.0
6
6
6
6
10
15
5.1 - 7.0
10
10
10
10
15
15
7.1 - 12.0
15
15
15
15
20
20
12.1 - 20.0
20
20
20
20
25
-
Summary of Contents for SGV115
Page 1: ...SGV115 English Page 04 French Page 11 Page 26...
Page 2: ...ENGLISH Original instructions 2 A B C 2 3 10 9 6 7 8 4 5 1 3...
Page 27: ...N516691 10 2017...
Page 28: ......
