ENGLISH
(Original instructions)
6
as, but not limited to, grinding dust, metal chips,
steel wool, aluminum foil, or any buildup of
metallic particles should be kept away from
charger cavities. Always unplug the charger
from the power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean.
♦
DO NOT attempt to charge the battery pack with
any chargers other than the ones in this manual.
The charger and battery pack are specifically designed
to work together.
♦
These chargers are not intended for any uses other
than charging STANLEY rechargeable batteries.
Any other uses may result in risk of fire, electric shock
or electrocution.
♦
Do not expose charger to rain or snow.
♦
Pull by plug rather than cord when disconnecting
charger.
This will reduce risk of damage to electric plug
and cord.
♦
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
♦
Do not use an extension cord unless it is absolutely
necessary.
Use of improper extension cord could
result in risk of fire, electric shock, or electrocution.
♦
Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal
heat.
Place the charger in a position away from any
heat source. The charger is ventilated through slots in
the top and the bottom of the housing.
♦
Do not operate charger with damaged cord or plug
— have them replaced immediately.
♦
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way.
Take it to an authorised service centre.
♦
Do not disassemble charger; take it to an
authorised service centre when service or repair is
required.
Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
♦
In case of damaged power supply cord the supply cord
must be replaced immediately by the manufacturer, its
service agent or similar qualified person to prevent any
hazard.
♦
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock.
Removing the battery pack will not
reduce this risk.
♦
NEVER
attempt to connect 2 chargers together.
♦
The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage.
This does not apply to the
vehicular charger.
SAVE THESE INSTRUCTIONS
Chargers
The SC201/ SC202 accept 18V batteries.
These chargers require no adjustment and are designed to
be as easy as possible to operate.
Charging Procedure (fig. B)
1. Plug the charger into an appropriate outlet before
inserting battery pack.
2. Insert the battery pack (6) into the charger. The red
(charging) light will blink continuously indicating that the
charging process has started.
3. The completion of charge will be indicated by the red
light remaining ON continuously. The pack is fully
charged and may be used at this time or left in the
charger.
Note:
To ensure maximum performance and life of Li-Ion
batteries, charge the battery pack fully before first use.
Charging Process
Refer the tables below for the state of charge of the battery
pack.
State of charge–SC201/SC202
charging ― ― ― ―
fully charged
hot/cold pack delay ― ― ― │
Hot/Cold Pack Delay
SC201/ SC202
When the charger detects a battery that is hot, it
automatically delays charging until the battery has cooled.
When the charger detects a battery that is cold, it
automatically delays charging until the battery has warmed.
The red light will continue to blink, but a yellow indicator
light will be illuminated during this operation. Once the
battery has cooled, the yellow light will turn off and the
charger will resume the charging procedure.
Stanley Li-Ion tools are designed with an Electronic
Protection System that will protect the battery against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the Li-Ion
battery on the charger until it is fully charged.
Li-Ion BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge.
