Stanley SCD2, Manual

Page: 7 / 72

7
ENGLISH
These chargers require no adjustment and are designed to be
as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger (j) into an appropriate outlet before
inserting battery pack.
2. Insert the battery pack (g) into the charger. The red
(charging) light will blink continuously indicating that the
charging process has started.
3. The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and
may be used at this time or left in the charger.
NOTE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery pack fully before first use.
Charging Process
Refer the tables below for the state of charge of the battery
pack.
State of charge–SC201
charging –– –– –– –– ––
fully charged ––––––––––––––––––––
hot/cold pack delay –– –– –– –––––––
HOT/COLD PACK DELAY
SC201/ SC202
When the charger detects a battery that is hot, it automatically
delays charging until the battery has cooled.
When the charger detects a battery that is cold, it automatically
delays charging until the battery has warmed.
The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery has
cooled, the yellow light will turn off and the charger will resume
the charging procedure.
Stanley Li-Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the Li-Ion battery on the
charger until it is fully charged.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the Li-Ion battery on the
charger until it is fully charged.
Important Safety Instructions for All Battery
Packs
When ordering replacement battery packs, be sure to include
catalog number and voltage.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non-compatible
charger as battery pack may rupture causing serious
personal injury.
• Charge the battery packs only in STANLEY chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in
locations where the temperature may reach or
exceed 40 ˚C (105 ˚F) (such as outside sheds or
metal buildings in summer).
WARNING: Never attempt to open the battery
pack for any reason. If battery pack case is
cracked or damaged, do not insert into charger.
Do not crush, drop or damage battery pack.
Do not use a battery pack or charger that has
received a sharp blow, been dropped, run over
or damaged in any way (i.e., pierced with a nail,
hit with a hammer, stepped on). Electric shock
or electrocution may result. Damaged battery
packs should be returned to service centre for
recycling.
CAUTION: When not in use, place tool on
its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools
with large battery packs will stand upright on the
battery pack but may be easily knocked over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when lithium ion battery packs are
burned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for
15 minutes or until irritation ceases. If medical attention is
needed, the battery electrolyte is composed of a mixture
of liquid organic carbonates and lithium salts.