Stanley GW1200 Installation & Configuration Manual Download Page 32 | Manualshive

Page: 32 / 35

background image

GW1200 Gateway Installation & Configuration Guide

32

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.

RoHS

RoHS Directive – 2011/65/EU

CE Conformance

IEC 60601-1:2005/EN 60601-1:2006

Medical Electrical Equipment

IEC 60950-12005

ESTI EN 301 498-1:V2.1.1

ESTI EN 301 498-17:V3.1.1

Warranty

STANLEY Healthcare (“STANLEY”) Standard Warranty and Disclaimer

«
...
30
31
32
33
34
...
»

Summary of Contents for GW1200




































Reviews:

No comments

Related manuals for GW1200

ECL Comfort 110

Brand: Danfoss Pages: 8

NETWORK INTERFACE CARDS

Brand: Secure Computing Pages: 17

Brand: Seneca Pages: 22

Brand: M-system Pages: 7

INKNXMIT015C000

Brand: HMS Pages: 32

Flight Stream 110/210

Brand: Garmin Pages: 46

AS Series ASM200

Brand: Quintum Pages: 3

DX Series DX2008

Brand: Quintum Pages: 15

Brand: King Pigeon Pages: 52

Brand: King Pigeon Pages: 55

Brand: Crow Pages: 29

Brand: Planet Pages: 2

Brand: Planet Pages: 53

Fieldgate FXA42

Brand: Endress+Hauser Pages: 118

Brand: AirLive Pages: 234

Brand: AirLive Pages: 247

Brand: Hybertone Pages: 48

Proventia MX3006

Brand: IBM Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands