3
1.3 OPERATING HAZARDS
•
When the tool is operated it must not be held in the hand or be in contact with any part of the body. There is a
possibility of a shear injury when the piston retracts.
•
Use of the tool can expose the operator’s hands to hazards, including crushing, impacts, cuts and abrasions and heat.
Wear suitable gloves to protect hands.
•
Release the start-and-stop device in the case of an interruption of the hydraulic supply.
•
Use only lubricants recommended by the manufacturer.
•
Contact with hydraulic fl uid should be avoided. To minimise the possibility of rashes, care should be taken to wash
thoroughly if contact occurs.
•
Material Safety Data Sheets for all hydraulic oils and lubricants is available on request from your tool supplier.
•
If the tool is fi xed to a suspension device, make sure that the fi xation is secure.
•
Beware of the risk of crushing or pinching if nose equipment is not fi tted.
•
DO NOT operate tool with the nose casing removed.
•
When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent activation.
•
DO NOT abuse the tool by dropping or using it as a hammer.
•
Care should be taken to ensure that spent mandrels do not create a hazard.
1.4 REPETITIVE MOTIONS HAZARDS
•
When using the tool, the operator can experience discomfort in the hands, arms, shoulders, neck or other parts of the
body.
•
While using the tool, the operator should adopt a comfortable posture whilst maintaining a secure footing and
avoiding awkward or off -balance postures. The operator should change posture during extended tasks; this can help
avoid discomfort and fatigue.
•
If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing, aching, tingling,
numbness, burning sensations or stiff ness, these warning signs should not be ignored. The operator should tell the
employer and consult a qualifi ed health professional.
1.5 ACCESSORY HAZARDS
•
Disconnect the tool from the hydraulic supply before fi tting or removing the nose assembly or accessory.
•
Use only sizes and types of accessories and consumables that are recommended by the manufacturer of the tool; do
not use other types or sizes of accessories or consumables.
1.6 WORKPLACE HAZARDS
•
Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by use of the tool and
also of trip hazards caused by the air line or hydraulic hose.
•
Proceed with care in unfamiliar surroundings. There can be hidden hazards, such as electricity or other utility lines.
•
The tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electric
power.
•
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by use of the tool.
•
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
•
Care should be taken to ensure that spent mandrels do not create a hazard.
1.7 NOISE HAZARDS
•
Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus
(ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and the implementation of appropriate
controls for these hazards are essential.
•
Appropriate controls to reduce the risk may include actions such as damping materials to prevent workpieces from
“ringing”.
•
Use hearing protection in accordance with employer’s instructions and as required by occupational health and safety
regulations.
•
Operate and maintain the tool as recommended in the instruction manual, to prevent an unnecessary increase in the
noise level.
1.8 ADDITIONAL SAFETY INSTRUCTIONS FOR HYDRAULIC POWER TOOLS
•
The operating hydraulic supply must not exceed 217 bar (3200 PSI).
•
Oil under pressure can cause severe injury.
•
Do not fi t fl exible hydraulic hoses rated at less than 700 bar (10,000 PSI) working pressure at a fl ow rate of 2.73 l/min
(200 in 3/min).
•
Disconnect hydraulic hoses from the pump unit when tool is not in use, before changing accessories or when making
repairs.
•
Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fi ttings.
O R I G I N A L I N S T R U C T I O N
E N G L I S H
