background image

10 

CLEANING / MAINTENANCE 

 

Initial Cleaning: 

Prior to operating your new griddle, thoroughly wash the griddle surface and the exterior with a mild detergent 
or soap solution. Do not use abrasive cleaners since this might damage the cabinet finish. If the stainless steel 
surfaces become discolored, scrub by rubbing only in the direction of the finished grain. 

Cleaning: 

1.  Always turn unit off and allow it to cool completely before cleaning. Clean thoroughly before first use.  

2.  After each use, clean the griddle with wire brush or flexible spatula.  

3.  Once a day, thoroughly clean splash back, sides and front. Remove the grease drawer, empty it and wash 

it out.  

4.  Once  a  week,  clean  the  griddle  surface  thoroughly.  If  necessary,  use  a  griddle  stone,  wire  brush  or  steel 

wool on the surface. Rub with the grain of the metal while the griddle is still warm. A detergent may be used 
on  the  plate  surface  to  help  clean  it;  but,  care  must  be  taken  to  be  sure  the  detergent  is  thoroughly 
removed. After removal of the detergent, the surface of the plate should then be covered with a thin film of 
oil to prevent rusting. Clean stainless surfaces with a damp cloth and polish with a soft dry cloth. To remove 
discoloration,  use  a  nonabrasive  cleaner.  After  each  "weekly"  cleaning,  the  griddle  must  be  seasoned 
again.  If  the  griddle  usage  is  very  high,  the  "weekly"  cleaning  procedures  may  be  done  more  often  than 
once a week.   

Extended Shutdown: 

Turn the manual shutoff valve to "OFF"; (field installed valve not supplied by the manufacturer); turn all control 
knobs to the "OFF" position; and shut off the pilot flame by turning the adjustment on the pilot valve.  

*

NOTE

:

 Gas shutoff valve is supplied by the manufacturer on CE or European Community models.  

If the griddle is to be shut down for an extended period, put a heavy coat of grease over the griddle plate. 

SERVICE / REPAIR 

 

 

NOTE: THIS APPLIANCE MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT. 

 

NOTE:

  Parts  protected  by  the  manufacturer  or  his  agent  are  not  to  be  adjusted  by  the  installer  

 

unless the installer is an authorized service agent. 

If you have any questions or problems contact your nearest TRI-STAR Service Representative. 

Summary of Contents for Tri-Star TSHMG-2424i



















Reviews: