Standard APC-45 Replacement Manual Download Page 4

Page: 4 / 11

The following procedures show how to remove

the knife.

Turn on the power switch.

- The indication [REPLACE MODE] is shown on

the guide window and then it changes to [LOWER

CLAMP].

Press the cutting buttons.

- Only the clamp lowers and stops.

- The indication [TURN OFF POWER REPLACE

KNIFE] is shown on the guide window

Turn off the power switch.

Screw the knife replacing tools in.

- Screw the knife replacing tools into the screw

holes No.2 and No.5.

WARNING

Tighten the tools by hand as much as
possible. The knife will be supported just
by these two tools when removing the
knife.

APC-45 Knife Replacement

OFF

KNIFE REPLACE MODE

LOWER CLAMP

TURN OFF POWER
REPLACE KNIFE

OFF

Clamp

Knife

Cutting Buttons

NOTE

If the knife replacing tool cannot be screwed
because the screw hole is as shown in the figure
above -

1) Loosen the knife fixing screws,

2) Raise the fixing screw using the box wrench
which is used to loosen the knife fixing screws,

3) Bring out the screw holes and screw the knife
replacing tools in.

Knife

Knife Holder

Knife Replacing Tools

Summary of Contents for APC-45












Search results

Summary of Contents for APC-45

Reviews:

Related manuals for APC-45

Brands by name

Popular brands

Standard APC-45, Replacement Manual

Search results

Summary of Contents for APC-45

Reviews:

Related manuals for APC-45

Brands by name

Popular brands