manualshive.com logo in svg

Standard Change-Makers BCX-FRONT, Installation Instructions Manual, Page: 12 / 12

Share
Download
Standard Change-Makers BCX-FRONT Installation Instructions Manual Download Page 12

12

Cabinet

Model

ADA Requirements

Maximum Installation Height

Floor to Cabinet bottom 

(inches) 

Base  

Height 

(inches)

Header 

Height 

(inches)

For maximum mounting height the cabinet without a coin acceptor or printer can sometimes be mounted higher 
and meet ADA requirements. (See Chart Above) 

* If a mounting height with no coin acceptor is used and a coin acceptor is added at a later date then the 
machine would no longer meet ADA Requirements. 

# If a mounting height with no printer is used and a printer is added at a later date then the machine 
would no longer meet ADA Requirements. 

Test the Machine Operation 

When installation is complete, test each machine function for proper payout and 
operation.

1.

 

Fill the hoppers until the black area at the bottom is covered. 

2.

 

Insert monetary bills in the bill acceptor.

3.

 

Count the coins dispensed.

 

 

FOR ADDITIONAL QUESTIONS OR ASSISTANCE IN 

INSTALLING STANDARD CHANGE-MAKERS, INC. PRODUCTS, 

PLEASE CONTACT OUR SERVICE DEPT.

 

Standard Change-Makers, Inc. 

3130 N. Mitthoeffer Road 

Indianapolis, IN 46235-2400 

TOLL FREE: 1-800-968-6955 

PHONE: 317-899-6966 

FAX: 317-899-6977 

WEB: 

www.standardchange.com

 

EMAIL: 

[email protected]

 

Summary of Contents for BCX-FRONT













Reviews:

No comments