Stahl KB2 Operating Instructions Manual Download Page 34

Page: 34 / 68

Operating Instructions KB2 Keyboards

Mounting and installation

Page 34 of 68



R. STAHL HMI Systems GmbH / OI_Keyboard_KB2_en_V_01_00_02.docx / 07.03.2022

7.4

Installation

Explosion hazard due to improper installation !

Non-compliance may result in fatal or serious injuries.



Ensure the atmosphere is non-explosive.



Make sure that the device is not damaged.



If the device is connected to the mains:

Disconnect the device from the power supply.

Explosion hazard due to electrostatic charge!

Non-compliance may result in fatal or serious injuries.



Do not paint / coat the device or retouch its paint / coating. All

repairs must be carried out by the manufacturer.



If additional sticky labels are attached, the specifications of

EN IEC 60079-0 must be observed.



Clean the device with a damp cloth only.

7.4.1

General information on electric connection



Connect cables carefully.



Do not screw down on the conductor insulation.



Do not switch conductors.



Observe code of practice when connecting conductors.



Firmly screw down conductors.



Cables are attached ex factory and must not be extended or replaced.



The KB2 device versions are fitted with an 8-pole cable (+ shield conductor), and the PD2

versions with a 4-pole cable (+ shield conductor).



Shield the cable with a maximum of 1

MΩ against ground.



Twist the D+ and D- data

conductors

until right up to their terminals.



Pay attention to specified torques for screws to avoid damage to threads.



Suitable measures against electrical surge during lightning strike may be necessary.



Only connect and operate keyboards with the same protection level (see note on "

Protection

level

") !



For the connection of keyboards to IT-xx7 non-Ex devices use the "Non-Ex connector KB2

set" (2x USB connector) (SAP no. 301224) !

7.4.2

Connecting the device

1. Connect the USB conductors according to the terminal diagram (see chapter

19.1 Connection overview terminal assignment KB2)

2. Make sure the pin assignment is correct.

7.4.3

Grounding the device



Connect the shield with the cable lug to the PA ground connection (see chapter

19.1 Connection overview terminal assignment KB2

DANGER

Summary of Contents for KB2





































































Search results

Summary of Contents for KB2

Reviews:

Related manuals for KB2

Brands by name

Popular brands

Stahl KB2, Operating Instructions Manual

Search results

Summary of Contents for KB2

Reviews:

Related manuals for KB2

Brands by name

Popular brands