background image

Mounting and installation

14

244627 / 652560300010

2017-07-13·BA00·III·en·03

Floodlight LED

Series 6525

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

7.3.2 Cable entries

Cable glands and stopping plugs must be approved for the following types of protection:

a) restricted breathing (nR) and dust (IIIC)

b) increased safety (e)

Please observe the following, if cable glands and stopping plugs are used, but not 

provided by R. STAHL Schaltgeräte GmbH:

• Permissible cable diameter range, torques, temperature range of use

• IP level of protection, at least IP 65 or according to details on rating plate

• Operating instructions of the cable glands and stopping plugs

additionally, observe the following for cable glands and stopping plugs of the type of 

protection "increased safety" (e):

• valid EC type examination certificate and 

• confirmation of the manufacturer for the combination of the cable and screw 

connection

WARNING

Not approved cable glands and stopping plugs.

Explosion protection is impaired!

• Only use separately certified cable glands and stopping plugs.

Recommendation:

Use of cable glands and stopping plugs supplied by 

R. STAHL Schaltgeräte GmbH.

• see data sheet on our homepage www.stahl-ex.com.

DANGER

Explosion hazard if breathers are used!

Accidents or fatal injury are almost certain to happen!

• Do not use breathers.

Summary of Contents for 6525 Series






















Reviews: