Stahl 2000 Series Owner'S Manual Download Page 17

Page: 17 / 37

MOUNTING INSTRUCTIONS

2000 SERIES OWNER’S MANUAL

2000H MOUNTING INSTRUCTIONS

5. Most floors in truck bodies are not strong enough to mount a crane. You must use a 0.50” thick steel plate to

reinforce the floor before you mount the crane. The reinforcing plate must be welded to the rear chassis cross

member, intermediate cross member and the longitudinal support. For best results, weld 2 inches long on 6

inch centers.

6. Layout the mounting holes on the mounting surface. Drill four (4) 0.531” diameter holes and flame cut or

drill the 5.00” diameter hole.

7. Lift the crane into position. Make sure the power lead and the two (2) hydraulic hoses are fed through the

five-inch (5”) diameter hole.

8. Bolt the 2000 crane to the mounting surface with four (4) 0.50” grade eight bolts and four (4) grade eight

lock nuts. Torque the 0.50” bolts to 75 foot-pounds. Use of other than 0.50” grade eight bolts and lock nuts

may result in the crane breaking loose from the mounting surface when in use.

View thousands of Crane Specifications on FreeCraneSpecs.com

Summary of Contents for 2000 Series






































Search results

Summary of Contents for 2000 Series

Reviews:

Related manuals for 2000 Series

Brands by name

Popular brands

Stahl 2000 Series, Owner'S Manual

Search results

Summary of Contents for 2000 Series

Reviews:

Related manuals for 2000 Series

Brands by name

Popular brands