Figure1 Cyclone Vertical LED Fogger Functions
Getting Ready
All products are thoroughly tested at the factory and shipped in perfect
condition. If damage has occurred during shipping, or if components are
missing, please contact your local dealer immediately.
Your package should include:
1.
One
BREEZFOG 450
2.
One Controller
3
. One product user manual
Maintenance
Before doing maintenance, please make sure that the power is cut, the
power cord is unplugged, and the machine itself has cooled down.
The maintenance must be done by qualified person.
• The fog liquid is not allowed to get dirty. Be sure to always clean or
replace the caps on the fog liquid vessel and tight the cover of the fog
machine liquid tank immediately after filling.
• Periodically check the connections among the oil tube, the pump and
the heater to see if there’s oil leaking. If positive, lock tight the
connections carefully with proper tool.
• PC board should be kept from being dirtied with oil. In case this
happened, dismantle carefully the PCB, and have it brushed clean both
sides with dilute alcohol. Leave it dry itself, then install it back. Make
sure all wires are well connected.
• Clean the metal cover with dry cloth.
Note other important detail:
Plugging
FREEZFOG 450
in, the red LED under tank bottom will glow
indicating power on & warming-up. Check if with correct voltage in case it
doesn’t glow. A lit green LED under tank bottom appears as warm-up
arrives at fogging point, indicating a finished heating time (ready to fog).
Note that fog machines develop condensation around the output nozzle.
This may result in moisture accumulation on the surface below the output
nozzle. Consider this condensation when installing the unit.
All fog machines may sputter small amounts of fog occasionally during
operation and for a minute or so after being turned off.
Should there be any low fog emitted, running noisily or hindered fogging,
pull out the plug immediately. Check if string enough fog fluid, or if
outside fuse, controller connection and power supply improper, if not,
plug-in again, still persists abnormal running, check if with an unhindered
pipe, with flowing fluid. If causation is unclear, stop running to avoid
any damage, shut down to cool it, and bring unit to your local agent or
appointed service place for inspection, prohibit any dismantlement by
yourself.
** Although the LED is installed beneath the liquid tank, user can see change of the
color and the blinking speed by looking directly at the tank.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution
is found. Once the unit operates properly, do not carry out following steps.
If the problem persists, refer servicing to a qualified technician.
Power Connected but No Fog Is Emitted
1.
Check the power supply. Plug the unit into grounded electric power
supply socket with proper voltage.
2.
Check your controller if in correct connection, test the battery if power
enough for wireless controller.
3.
Disconnect fog machine from electric power supply. Replace fuse with
one of the same type.
Name
BREEZFOG 450
Item No.
BREEZFOG
Tank (liters)
0.5L
Heater Power
400W
Bracket
YES
Power Consumption
420W
Dimensions(LxWxH W/Handle)
230x142x140 mm
FUSE(120V)
T6.3A/250V
Weight (kg) without controller
1.5 kg
FUSE(230V,240V)
T4A/250V
Voltage
120V,230V,240V
50/60Hz
Warm Up time(min)
4
Matching Controller (Included)
LC-2N
Fog Output (cu.ft/min)
2000
Matching Controller (Optional)
RC-2N
Fluid consumption (ml/min) 15ml/min
Product Specifications
Appendix – B RC-2N
Wireless Remote Control Operation:
The
BREEZFOG 450
is designed with wireless remote controller.
Workable remote distance possibly extends to 25 meters. Once the fog
machine is plugged, the red LED on this receiver of remote controller will
light up. When fog machine reached operating temperature, and has
ready for emission by pressing the button of transmitter. The fog
machine is off emission for about 4 minutes during warm-up and re-
heating cycles (about 40 seconds), and turns on when the temperature
reached again.
Connector: JY cable Function:
Wireless ON/OFF
A
- JY cable
B
- Button
C
- Green LED (fog)
D
- Red LED (power)
* Voltage is preset at the factory and may not be changed.
Appendix – A LC-2N
Wired Remote Control Operation:
The
BREEZFOG 450
is designed with 3m wired remote controller with JY
cable. Once the fog machine is plugged, the red LED on this remote
controller will light up. When fog machine has reached operating
temperature, the green LED lights up, and indicating the fog machine has
ready for emission by pressing the button. The green LED is off for about
4 minutes during fog machine warm-up and re-heating cycles (about 40
seconds), and turns on when the fog machine becomes workable.
Cable Length: 3m
Connector: JY cable
Function: ON/OFF
A
- JY cable
B
- Button
C
- Green LED (ready)
D
- Red LED (power)
Page 4
Page 5
Page 6
Page 7
A
C
C
B
D
A
B
D
Model
LC-2N
RC-2N
Cable Length
8m
Wireless
Effective Distance
N/A
Up to 25 m
Connector
JY cable
JY cable
Function
ON/OFF
ON/OFF
Dimension (LxWxH)
90 x 50 x 24 mm
90 x 50 x 24 mm
Weight
0.28 kg
0.1 kg
Set Up
1.
Open the shipping carton and carefully remove the unit from the
shipping carton.
2.
Be sure to remove packing material from around the fog machine,
especially near the nozzle.
3.
Set the fog machine on a dry, flat surface.
4.
Use only high quality, water-based fog fluid.
5.
Firmly attach the remote control mechanism to socket (C of figure1)
on the back of the unit.
6.
Plug mains power cord from the fog machine into appropriate power
supply socket. Wait about 4 minutes for heating element to heat up.
7.
Refer to your controller manual for operation details. (Appendix A)
8.
If fog is emitted continuously for a long time, the heating element
temperature may drop, shutting off fog production. If so, please do
not activate for emission. Wait briefly. When the heating element
temperature rises, fog emissions can be resumed.
Operation
Remote Control Operation .....................................................................
For best result, please use LC-2N line controller or RC-2N wireless controller.
1.
Firmly attach the remote control to socket (C of figure1) on the back of
the unit.
2.
Plug mains power cord from the fog machine into appropriate power
supply socket. A lit red LED under the tank indicates that the fogger is
power on. Wait about 4 minutes for heating element to heat up, a lit
green LED under the tank indicates that the fogger is ready to fog.
3.
Refer to your controller manual for operation details. (Appendix A & B )
