background image

Page

 

 

 

 

 

            

ST325 User Handbook

 

To exit programming mode at any time wait 10 seconds without 
pressing any keys - the ST325 will then revert to the idle display.  
Alternatively press the START/STOP key to exit programming and to 
begin firing immediately. 

The

§

 

key can be used to reverse through the programming steps to 

correct errors or to exit programming mode. 

Available ramp rate displays are: 

End

… 

999

 

FULL

.  If  

End

 

is 

shown but another segment is required then push the 

©

 

key to obtain 

the required ramp rate (in the range 1°C/hr to 999°C/hr).  If full power 
is required then push the 

©

 

key until  

FULL

 

is displayed. 

Programming Notes 

Programming 

To declare the end of a program while prompted for a ramp rate push 
the 

ª

 key until 

End

 is displayed. 

FAQ (Frequently Asked Questions) 

During programming the COOLING lamp sometimes flashes when I want the 
kiln to heat - why is this? 

The ST325 asks you to input the ramp rate before it asks for the soak 
temperature so if the (still to be set) soak temperature in the current segment is 
less than the soak temperature in the previous segment the ST325 will assume 
cooling is required.  This anomaly will be rectified when all of the program has 
been entered.  This can be confirmed by stepping through the completed 
program with the 

¨

 key. 

Q: 
 

A: 

During programming the HEATING lamp sometimes flashes when I want the 
kiln to cool - why is this? 

The ST325 asks you to input the ramp rate before it asks for the soak 
temperature so if the (still to be set) soak temperature in the current segment is 
more than the soak temperature in the previous segment the ST325 will 
assume heating is required.  This anomaly will be rectified when all of the 
program has been entered.  This can be confirmed by stepping through the 
completed program with the 

¨

 key. 

Q: 
 

A: 

During programming 

End

 is displayed when I want to enter another segment - 

why is this? 

Available ramp rate displays are: 

End

… 

999

 

FULL

.  If  

End

 

is shown but 

another segment is required then push the 

©

 

key to obtain the required ramp 

rate (in the range 1°C/hr to 999°C/hr).  If full power is required then push the 

©

 

key until  

FULL

 

is displayed. 

Q: 
 

A: 

How do I declare the end of the program? 

Press the 

¨

 key to advance to the next segment.  Push the 

ª

 key until 

End

 

is  

displayed.  (Press the 

¨

 key again to exit programming mode).  

Q: 
 

A: 

ST325 User Handbook

 

 

 

 

 

       

Page

  

17 

Program Pause Facility 

While firing press and hold down the green f

n

 

(function) key then press the 

▌▐

 (pause) key.  The ST325 will pause the executing program.  To un-

pause the program repeat the above key press sequence.  The effects of 
pausing are as follows:- 
 
If paused during  ramping the kiln temperature will be held (soaked) 

indefi-

nitely

 at the current kiln temperature.  The ramp will continue when un-

pause is selected. 
 
If paused during soaking then the soak time will be 

extended indefinitely

.  

The remainder of the soak period will be resumed when un-pause is se-
lected. 
 
Segment advance

 

►►

can also be used to terminate the pause.  This will 

advance the segment and will immediately terminate a paused soak - ad-
vancing to the next segment (if any). 
 
Changes made to the operation of the ST325 in this way are temporary 
and are not stored. 

 600

 

°C 

°C/hr 

hr.min 

As a warning during pause a double 
beep is sounded every 10 seconds 
and the display scrolls 

PAUSed

.  The 

PAUSED lamp to the bottom left of 
the main display is lit. 

Adjusting While Firing 

WARNING - PROGRAM PAUSE 
The program pause facility should be used with care.  Program 
execution is suspended and the kiln will be held at its current 
temperature indefinitely.   
 
If left too long at high temperatures kiln damage could result. 

Summary of Contents for ST325













Reviews: