background image

Page 

     ST312A 

User 

Handbook 

MAIN DISPLAY 

SEGMENT 
MIMIC 
DISPLAY 

DISPLAY 
INDICATORS 

CONTROL 

KEYS 

(5) 

At A Glance 

DELAYED 
START LAMP 

t1 LAMP 

SOAK TIME LAMP 

SOAK TEMPERATURE LAMP 

RAMP 1 LAMP 

RAMP 2 LAMP 

At A

 Glance 

FIRING LAMP 

ºC

t

ST312A User Handbook 

 

 

 

 

       Page   19 

Sample Programs 

Name

 

Ramp 1

 

t1 

Soak time

 

Low Biscuit 

70°C/hr 
 

600°C 

00:15 

Normal Biscuit 

70°C/hr 
 

600°C 

00:15 

High Biscuit 

70°C/hr 
 

600°C 

00:15 

Earthenware Low 
Temperature Glaze 

90°C/hr 
 

600°C 

00:30 

Earthenware Mid 
Temperature Glaze 

90°C/hr 
 

600°C 

00:30 

Earthenware High 
Temperature Glaze 

90°C/hr 
 

600°C 

00:30 

Stoneware Glaze 

90°C/hr 
 

600°C 

00:30 

On Glaze Enamel 

90°C/hr 
 

600°C 

00:30 

Heavy Sculpture 

50°C/hr 
 

300°C 

00:30 

Lustre 

90°C/hr 
 

600°C 

00:00 

Ramp 2 

FULL 

FULL 

FULL 

FULL 

FULL 

FULL 

FULL 

FULL 

70°C/hr 

FULL 

Soak temp 

960°C 

1000°C 

1160°C 

960°C 

1040°C 

1140°C 

1250°C 

780°C 

1000°C 

750°C 

Sample Pr

ograms 

Notes

 

Earthenware High Temperature Glaze is also suitable for Stoneware Low 
Temperature Glaze. 
Stoneware Glaze is also suitable for Porcelain. 
On Glaze Enamel is also suitable for some enamelling work. 
Heavy Sculpture is also suitable for Terracotta. 

Summary of Contents for ST312A











Reviews: