STACYC Stability Cycle, Owner'S Manual

Page: 8 / 13

P a g e | 14 P a g e | 14 DOC 001 REV A DOC 001 REV A P a g e | 15
Power
→
”ON”
Throttle
→
5%-10% rotation
LED
→
Green, Yellow, Red
(Full Battery Charge)
Power Switch → ”OFF”
Throttle → ”FULL” position
HOLD THROTTLE IN FULL
POSITION!
Power
→
”ON”
Throttle
→
5%-10% rotation
LED
→
Red
(Low Battery Charge)
Power
→
”ON”
Throttle
→
5%-10% rotation
LED
→
Yellow and Red
(Med-Low Battery Charge)
5. If you continue to twist the throttle (10%+), the motor will be
activated. The more the throttle is twisted, the more power is
delivered to the motor, based on the power program selected.
6. Exercise caution around moving parts and wheels.
7. Contact STACYC customer service or go visit:
www.STACYCstabilitycycle.com if unsure about any operational
procedure.
CHANGING POWER MODES (FOR ADULT USE ONLY!!!!)
Your STACYC is equipped with 3 power modes for different skill levels. Training Mode,
Standard Mode and Advanced Modes. We do not advise showing children how to
adjust the modes. Each child should have the mode set by an adult who will be close -
ly supervising the child. DO NOT put your child on the “Advanced” mode without
working through the process of learning the Training and Standard Modes.
Activate Program Selection:
1. Ensure power switch is in “OFF” position.
2. Install Battery.
3. Ensure bike power switch is “OFF” and no LED lights are on, or no
beeps were heard.
o If any LED light is on, turn bike Power Switch to “OFF”
o If you heard a beep, turn bike Power Switch to “OFF”
4. Turn throttle gently and hold throttle in “FULL” position. Do
not release.
5. Turn power switch to “ON” position , do not let throttle move from
“FULL” position.
o The yellow LED light will flash 5 times, then all the LED lights
will flash and beep 5 times, all LEDs will remain lit. Wait 1 sec,
then release throttle. All LED lights should be off.
o If LED lights are on, repeat from step 3, and be sure not to
twist the throttle quickly as it is not in Program Mode!!!
Power Switch → ”ON”
Throttle → ”FULL” position
LED → flashing YELLOW
5 yellow flashes
Selection MODE:
Throttle
→ ”FULL” position
LED → solid GREEN
(training mode)
Selection MODE:
Throttle
→ ”MID” position
LED → solid YELLOW
(standard mode)
Selection MODE:
Throttle
→ ”LOW” position
LED → solid RED
(advanced mode)
Power Switch → ”ON”
Throttle → ”FULL” position
LED → flashing GREEN, YELLOW
AND RED
5 Green/Yellow/Red flashes with
5 beeps, all LEDS stay lit, release
throttle, all LED lights off, ready
to choose power model
Select Program:
6. Turn throttle, and as the throttle moves through the range of power
modes, the Red, Yellow, or Green LED light will illuminate.
7. Hold Throttle at the power mode (LED position) desired
approximately 5 seconds until “2 short beeps” are heard.
o Red→training mode (slow)
o Yellow→standard mode (medium)
o Green→advanced mode (fast)
Exit Program Selection:
8. Release throttle.
9. All LED lights flash together 1 time with “1 long beep”.
10. LED Light indicating selected power mode will now be illuminated!
o Operation of STACYC will be with the illuminated power
mode. STACYC will stay in this power setting unless changed
as per steps above:
o Red→training mode (slow)
o Yellow→standard mode (medium)
o Green→advanced mode (fast)