background image

DocID028183 Rev 1

17/40

UM1932

Hardware layout and configuration

39

          

Table 2. Arduino compatible connectors 

LEFT Connectors

CN No.

Pin No.

Pin Name

MCU Pin

Function

CN6 Power

1

-

-

Not connected

2

IOREF

-

3.3V Ref

3

NRST

NRST

Reset

4

+3V3

-

+3.3V input/output

(1)

1. Important, before using pin4 of CN6 as +3.3V input, insure the solder bridge SB8 is removed. 

Otherwise the board STM32F469I-DISCO could be damaged by the overcurrent.

5

+5V

-

+5V output

6

GND

-

Ground

7

GND

-

Ground

8

VIN

-

+6V to +9V power input

(2)

2. The external voltage applied to pin VIN should be in the range 6 to 9V at 25°C ambient 

temperature. If a higher voltage is applied the regulator U10 may overheat and could be 
damaged.

CN8 Analog

1

A0

PB1

ADC12_IN9

2

A1

PC2

ADC12_IN12

3

A2

PC3

ADC12_IN13

4

A3

PC4

ADC12_IN14

5

A4

PC5 or PB9

(3)

 

3. By default pin 5 and pin 6 of connector CN8 are PC5 and PA4 respectively. They are enabled 

by the default configuration of solder bridges: SB10 and SB12 closed, SB9 and SB11 opened. 
If necessary to have an I2C interface on pins 5 and 6 of connector CN8, change the 
configuration solder bridges: open SB10 and SB12, close SB9 and SB11.

ADC12_IN15 or 

I2C1_SDA

(3)

6

A5

PA4 or PB8

(3)

 

ADC12_IN4 or

 I2C1_SCL

(3)

 

Summary of Contents for UM1932









































Reviews: