ST STM8A-DISCOVERY User Manual Download Page 8

Features

UM1574

8/48

Doc ID 023645 Rev 1

3 Features

The STM8A-DISCOVERY offers different features combined with STM8AF and STM8AL 
boards:

STM8AF and STM8AL common board features:

On-board ST-LINK/V2 included for debugging and programming

Board power supply: through 5 V USB bus 

Internal dual ST662A step-up converter building the 12 Vdc when powered by USB 
port

External application power supply V

BAT

 (up to 14 Vdc)

16 MHz HSE XTAL crystal oscillator

L99PM62GXP power management IC with LIN and high speed CAN with SPI control 
interface and high-side drivers

Two push buttons (USER1 and USER2)

Extension header for L99PM62GXP including relays, high-side outputs and wake-up 
capabilities

STM8AF dedicated board features:

STM8AF5288T microcontroller featuring 64 Kbytes Flash, 2 Kbytes data EEPROM, 
LIN, CAN in an 48-pin package

Seven LEDs:

LD1 (red/green) for USB communication

LD2 (red) for 5 V power ON

Five user LEDs LD3 (red) and LD4 to LD7 (green)

RV1 potentiometer connected to the ADC peripheral

Extension headers for MCU connectivity (full Port B, free ports pins, RESET)

STM8AL dedicated board features:

STM8AL3L68T microcontroller featuring 32 Kbytes Flash, 1 Kbytes data EEPROM, 
LCD in an 48-pin package

Four LEDs:

LD1 (red/green) for USB communication

LD2 (red) for 3.3 V power ON

2 user LEDs LD3 (red) and LD4 (green)

4-digit alphanumeric LCD display including 4 bars display

Extension header for MCU connectivity (free ports pins, RESET)

Summary of Contents for STM8A-DISCOVERY

















































Reviews: