St. Croix Hastings Installation Manual Download Page 5 | Manualshive

Page: 5 / 24

background image

Page 4

Hastings Installations Manual

EXHAUST VENTING

VENTING: APPROVED MATERIALS

The  stove  requires  a  venting  system,  approved  for  pellet  stoves  by  a  certified  testing  lab.
Approved pellet stove venting materials are: 1) PL vent, a double wall vent with a stainless steel
liner;  and  2)  Single  wall  rigid  or  flexible  stainless  steel  pipe.  PL  Vent  and  Single  wall  vent  is
available through manufacturers such as: Simpson DuraVent, Energy Vent LTD, James A. Ryder
and  Selkirk  Metalbestos  and  is  carried  by  many  local  pellet  stove  dealers.  In  this  manual
approved  venting  will  be  referred  to  a  “PL  vent”  or  “Single  wall  vent”.  All  single  wall  vent
adaptors must be stainless steel.

NOTE:  TYPE  “B”  GAS  VENT  MUST  NOT  BE  USED  IN  ANY  PELLET  STOVE
INSTALLATION.

Examples of venting system components follow:

High temperature ceramic roping reduces potential fly ash escaping through joints.

Stainless steel inner liners resist corrosive flue gas damage to the system..

Flex pipe is 430 stainless steel, 4 ply construction with a total thickness of approx. .07 inches.

«
...
3
4
5
6
7
...
»

Summary of Contents for Hastings

























Reviews:

No comments

Related manuals for Hastings

Brand: Ravelli Pages: 56

Brand: Saey Pages: 41

Brand: Quadra-Fire Pages: 52

Brand: Breckwell Pages: 9

Brand: Last Calor Pages: 153

Brand: Max Burton Pages: 2

Brand: Easy@Home Pages: 26

ECONOMONOBLOCCO WT F Series

Brand: Palazzetti Pages: 94

Brand: Whirlpool Pages: 16

Brand: THERMOROSSI Pages: 32

COMPACT S22 EVO5

Brand: THERMOROSSI Pages: 59

Brand: Asaklitt Pages: 5

Brand: Camplux Pages: 32

Brand: J. A. Roby Pages: 16

Brand: Town & Country Fires Pages: 11

Brand: Palazzetti Pages: 84

Brand: Dometic Pages: 216

Brand: HappyHome Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands