St. Croix Hastings Installation Manual Download Page 22 | Manualshive

Page: 22 / 24

background image

Page 21

Hastings Installations Manual

4.  Permanently bolt the stove to the floor, (X).

5.  Electrically  ground  the  stove  and  pedestal  to  the  metal  chassis  of  the  home.  Use  a  number
eight, (8), gauge or larger copper wire, (Y).

6.  Maintain an effective vapor barrier at location where PL vent exits the structure.

7.  Check any other local building codes or other codes that may apply.

8.  Do no use components other than those specified for use with this unit, (Refer to pages 4, 5, 6
and 7).

9.  Floor protection requirement must be followed precisely.

10.    PL  Vent  must  be  used  for  exhaust  venting.  (Single  wall  vent  is  not  allowed).  Follow  PL
Vent manufacturer’s installation directions and observe all listed clearances to combustibles.

«
...
20
21
22
23
24
»

Summary of Contents for Hastings

























Reviews:

No comments

Related manuals for Hastings

Brand: Unical Pages: 16

Brand: Breckwell Pages: 10

Tradition P23FSA

Brand: Breckwell Pages: 2

Brand: Harman Pages: 18

Accentra 52i Pellet Insert

Brand: Harman Pages: 32

Brand: Ravelli Pages: 60

Brand: Rommelsbacher Pages: 16

Brand: WANDERS Pages: 60

Brand: Adexa Pages: 11

Brand: Starke Pages: 13

Brand: HASE Pages: 44

Brand: HASE Pages: 76

SIROCCO SC30L.NZ

Brand: Blaze King Pages: 48

Brand: Yakar Pages: 28

Brand: Primus Pages: 75

INSERIMENTI A70

Brand: Palazzetti Pages: 200

Brand: Palazzetti Pages: 128

Brand: Vogelzang International Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands