background image

Page 13 

Hastings Installations Manual 

 

b.

 

With

 Outside Air Connected to the unit. In this manner the appliance is a Direct Vent 

Appliance (sealed Combustion System) as listed in NFPA 211-6.  

 

3.3.3.2  Direct  Vent  Appliance  (Sealed  Combustion  System  Appliance)  A  system 
consisting  of  an  appliance,  combustion  air  and  flue  gas  connections  between  the 
appliance and the outside atmosphere, and a vent cap supplied by the manufacturer, and 
constructed  so  that  all  the  air  for  combustion  is  obtained  from  the  outside  atmosphere 
and all flue gases are discharged to the outside atmosphere. 
 

Special Venting Arrangements are listed in NFPA 211-31 
 

10.7.1.2 The Vent Terminal of a Direct Vent Appliance with an input of 10000 BTU/Hr or 
less shall be located at least 6” from any opening into a building, and such an appliance 
with  an  input  of  over  10000  BTU/Hr,  but  not  over  50000  BTU/Hr  shall  not  be  located 
less than 9” from any opening through which vent gases could enter a building, and the 
vent  terminal  of  such  appliance  with  an  input  over  50000  BTU/Hr  shall  be  located  not 
less than 12” from the opening. 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

Figure 4b 

 
 

9” (229 mm) ABOVE, BELOW OR HORIZONTALLY FROM a door, window, cavity, or air 
vent. 

Summary of Contents for Hastings

























Reviews: