manualshive.com logo in svg

SST Automation GT200-PN-CO, User Manual, Page: 3 / 32

Share
Download
SST Automation GT200-PN-CO User Manual Download Page 3

WWW.SSTAUTOMATION.COM

Catalog

1 Product Overview ......................................................................................................................................................1

1.1 Product Function ............................................................................................................................................ 1
1.2 Product Feature ...............................................................................................................................................1

1.2.1 CANopen Mode.................................................................................................................................. 1
1.2.2 CAN Mode.......................................................................................................................................... 2

1.3 Technical Specifications.................................................................................................................................3
1.4 Related Products .............................................................................................................................................6
1.5 Revision History.............................................................................................................................................7

2 Hardware Descriptions..............................................................................................................................................8

2.1 Product Appearance........................................................................................................................................8
2.2 LED Indicators............................................................................................................................................... 9
2.3 DIP Switch......................................................................................................................................................9
2.4 Interface........................................................................................................................................................10

2.4.1 Power Interface................................................................................................................................. 10
2.4.2 Ethernet Interface.............................................................................................................................. 10
2.4.3 CAN/CANopen Interface..................................................................................................................11

3 Hardware Installation.............................................................................................................................................. 12

3.1 Machine Dimension..................................................................................................................................... 12
3.2 Installation Method...................................................................................................................................... 12

4 Quick Start Guide....................................................................................................................................................13

4.1 Gateway Configuration................................................................................................................................ 13
4.2 Software Configuration................................................................................................................................14
4.3 Run............................................................................................................................................................... 18
4.4 Change Device IP and Name....................................................................................................................... 23

4.4.1 Scan Devices on LAN .......................................................................................................................23
4.4.2 Change IP Info and Name................................................................................................................. 24

4.5 IP Address Conflict Resolution....................................................................................................................26

5 Software Instructions...............................................................................................................................................29

Summary of Contents for GT200-PN-CO

































Reviews:

No comments