manualshive.com logo in svg

SST Automation GT200-PN-CO, User Manual, Page: 21 / 32

Share
Download
SST Automation GT200-PN-CO User Manual Download Page 21

WWW.SSTAUTOMATION.COM

18

4.3 Run

The data conversion between PROFINET network and CANopne/CAN of GT200-PN-CO is established by

"mapping". GT200-PN-CO has two data buffers, one is input buffer (384/128 bytes); the other is output buffer

(384/128 bytes).

CANopen acts as a master

Communication mode between CANopen and PROFINET is asynchronous mode, as shown below:

"Data 1" shows the data transfer process from PROFINET to CAN; "Data 2" shows the data transfer process from

CAN to PROFINET.

The gateway runs in CANopen network independently, and transmits read/write commands of CANopen

parameters periodically according object dictionary, also transmits and receives PDO commands. When receiving

I/O request from PROFINET, the gateway will instantly respond with the latest CANopen data to realize the

matching of network speed. This is what we called asynchronous mode.

TPDO and RPDO applies producer/consumer mode, and often be used in the occasion with high requirement

PROFINET

Summary of Contents for GT200-PN-CO

































Reviews:

No comments