SSS Siedle HTV 840-02, Product Information

Page: 20 / 50

14
13 Address setting using the sliding
switches.
(See programming instructions)
Dismantling
14 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board and
receiver remain on the upper part of
the housing.
Lettering
15 The lettering panel can be
inscribed to indicate the button
functions. The see-through panel
can be lifted at the side.
Setting the call tone volume
16 The potentiometer for setting the
call tone volume is accessible under
the lettering insert.
17 Assignment of device buttons.
Accessories for HTV 840-...
• ZTV 840-... for conversion from a
wall-mounted to a table-top unit.
Commissioning
Following correct completion of
mounting and installation, the
address is set at each unit while
disconnected from the power
supply
(Fig. 13, setting device
address). A maximum of 4 devices
can be given the same address,
meaning that these devices are then
switched in parallel. The system is
switched on in a central location and
is then ready for operation after a
short delay in its as-delivered status
(basic configuration 6).
Define the configuration
In the as-delivered status, basic
configuration 6 is always defined.
A configuration cannot be deleted
but only overwritten. Devices (HTV
840-...) can be given different
configurations within one system. In
this case, the performance scope of
the entire system is always oriented
to the lowest configuration stage.
However, mixed operation is only
admissible between configurations
1-3 & 4-6.
Programming switch setting
When programming manually, set
the slide switch 10 (FP) to "On" for
programming and then return to
"Off" for the operating status. If
there is an SCO 740-... integrated in
the system, the switch must always
be set to "Off".
Basic configuration
The 6 defined basic configurations
can be accessed without any
additional aids. With the sliding
switch 10 (FP) switched on press
the light and door release button
simultaneously, hold down and
additionally press the numbers (1-6)
for the required configuration.
After appr. 3 seconds, the two
LEDs under the door release and
light button briefly light up. The
configuration for this device is now
confirmed. An acknowledgement
tone also sounds in the handset.
The sliding switch 10 (FP) must
be switched off again after
configuration.
System configuration
With the aid of the system
configuration, all connected
HTV 840-... units can be individually
configured with all the system's
possible combinations. The
basic requirement for system
configuration is always the system
controller SCO 740-...
Using a PRI 602-... , a PC can be
connected which simplifies the
configuration process and permits
the configurations of all users
to be exported, modified, saved
and printed out. For more details,
please refer to the programming
instructions for the SCO 740-...
Extended configuration
In the extended configuration,
suitably trained specialists have the
opportunity to carry out individual
changes in the configuration.
However, a thorough understanding
and knowledge of the system are
mandatory for this.
Video memory
The picture save function is
deactivated in the as-delivered
status. If required, it has to
be activated using the SCO
programming software. This
function is only possible provided
a sufficient video power supply is
available!
If a picture is saved, this is indicated
by the LED underneath the DR
button.
The display can be set using the
programming software to any
optional LED. In addition, an
optional button can be assigned the
function „Display saved pictures”
for direct access to the saved picture
library. In the as-delivered status,
saved pictures can be accessed using
the Enter button.
The device‘s video memory is able
to save 28 pictures from the door
camera.
Pictures saved in the device are
erased after a power failure.
If the system includes cameras with a
swivel and tilt function, the direction
buttons of the video control system
can be used to actuate the swivel
and tilt movements.
When selected using the „Control“
button, the picture remains full size
on the screen and the camera can
be controlled using the direction
buttons. Using the „Back“ function,
the video module is returned to
normal mode.
For more detailed information,
contact the Siedle-Multi hotline
Tel. +49 7723 63-378