manualshive.com logo in svg

SSS Siedle DCIP 650-01, Manual

Share
Download
SSS Siedle DCIP 650-01 Manual Download Page 24

24

A number of steps have to be  
executed for commissioning the 

DCIP 650-... . The specified sequence 

must be adhered to without fail.

• Prior to programming the 

DoorCom IP 650­... the entire 
In­Home system must be pro­
grammed and documented with the 
bus programming software  
BPS 650­... .

• Complete programming of the 

DoorCom IP 650­... takes place 
using the bus programming software 
BPS 650­... via the SII 650­...

6 Commissioning
DCIP 650-01

Connection of the PC to SII 650-...

Step 1 
Issue of the IP address and 

subnet mask in the IPVS 600‑...

• The connection can be established 

using a crossover network cable. The 

IPVS 600-... can also be addressed 

via the network if the PC and 

IPVS 600-... are located in the same 

address area. 

• Start the Internet Explorer on the 

PC and enter the following in the 
address line: 
http://192.168.0.1 
The IP settings in the as­delivered 
status of the IPVS 610­...  
IP address: 192.168.0.1 
Subnet mask: 255.255.255.0 

Gateway address: 0.0.0.0

 

User name: Service  
Password: None issued on 
delivery 

The user interface is opened. 

• Select the 

Expert mode

 menu 

item. 

• Under

Expert mode

 select the 

menu point 

Network 

• The following settings can be 

performed for operation in the 
network: 
DHCP 
IP address 
Subnetmask address 

Gateway address

 

DNS server address 
Changes to the IP address, subnet 
mask address or gateway address 
are transmitted to the device by 
clicking on the 

Set

 button. However, 

these only become valid after 
restarting the device. 

• After entering a new IP address, 

click onto the 

Set

 button 

• Enter the old IP address in 

the address line of the web 
browser, followed by /reset (e.g. 
192.168.0.11/reset). The IPVS 600 is 
restarted and can subsequently only 
be reached using the new IP address. 
The connection is established 
between the PC and IPVS 600 ... .

Changes to the IP address or subnet 
mask address are transmitted to the 
device by clicking on the 

Set

 button. 

However, these only become valid 
after restarting the device. 

• After entering a new IP address, 

click onto the 

Set

 button. 

• Enter the old IP address in the 

address line of the web browser, 
followed by /reset (for example 
192.168.0.1/reset). The IPVS is 
restarted and can subsequently only 
be reached using the new IP address.

Step 2 
Read out In-Home bus

All existing devices within the 
In­Home bus are read in and are 

then visible in the BPS 650-... as a 
tree structure. Each BVNG 650-... 

possesses a unique address. This 
must be set the same at the 

SII 650-... and SIVS 610-... .

Summary of Contents for DCIP 650-01

































Reviews:

No comments

Brands by name

Popular brands

Load more brands