background image

14

LED displays SIVS 610-0

LED signalling IPVS 600-...

The IP video server IPVS 600­... has 3 LEDs which can display operating statuses and can provide an indication of 
possible errors: LED power on the top and the LED LINK and LED ACT on the underneath.

LED Power

Function

OFF

IPVS 600­... is switched off.

Lights up in green

IPVS 600­... is switched on

Flashes green

Access to the IPVS 600­...

Lights up in red (briefly)

Start process running

Lights up in red (continuous)

Error in the device or failed upload

LED LINK

Lights up in green

Network connection exists

LED ACT

Lights up in orange

Active data transmission via the network

LED signalling SIVS 610-...
Switching on

LED green

LED red

Function

OFF

ON

After reset, power on: Device boots to operating status.

ON

ON

The boot area is checked. Software runs in the flash

Fast flashing

ON

After a software update, the boot area is recreated.  
This can take up to around 3 minutes.

Operation

LED green

LED red

Function

ON

OFF

Booting is complete. All OK. Normal status

Slow flashing

OFF

Display, a connection exists

Fast flashing

OFF

A software update or reconfiguration process is under 
way

Fault

LED green

LED red

Function

OFF

Slow flashing

ERROR, software running only in bootloader. Program 

memory defective. (Device defective, possibly new 
software update or exchange.)

ON

Slow flashing

Vario bus address error (error remedy possible on site)

ON

Fast flashing

The 12 V power supply (terminal bv, cv) is overloaded. 

(Error remedy possible on site)

OFF

OFF

If supply voltage is definitely connected, the device is 
defective. (Exchange)

Frequencies: Slow appr. 2 Hz, fast appr. 16 Hz

Summary of Contents for DCIP 650-01

































Reviews: